Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Make signs from Trotec materials
Our new tutorial offers templates for the quick and easy creation of Covid-19 signage using various Trotec materials and your laser engraving machine.
Wash your hand's sign - Variant 1
Wash your hand's sign - Variant 2
This sample can be produced with any other Speedy laser engraving machine.
When working with TroLase or TroLase Foil, if you are using the entire work surface, a vacuum table or an adhesive mat can be used so that the material lies flat over the entire surface. Otherwise, cover the work surface with paper to create an optimal vacuum.
You can either use our pre-made template or create your own design files. Use the settings below to send the job to the laser.
Important: If you use TroGlass Reverse, the file must be mirrored.
Process mode | Resolution | Cut line |
---|---|---|
standard | 500dpi | none |
Halftone | Other |
---|---|
- | Optimised geometries, inner geometries first |
The next step is to create the parameter settings. Our suggested parameters will differ depending on the laser engraving machine used and the available laser power. Before processing the TroLase and TroLase Foil sheets the protective foil should be removed before placing it into your laser. If TroGlass Reverse is used, we recommend removing the foil after laser processing.
Material | Colour | Process | Power (%) | Speed (%) | ppi/Hz | Passes | Air Assist | Z-Offset | Direction | Advanced |
---|---|---|---|---|---|---|---|---|---|---|
TroLase Foil | black | Laser Engraving CO2 | 55 | 80 | 500 | 1 | off | 1.5 | bottom to top | - |
red | Laser Cutting CO2 | 40 | 1 | 2000 | 1 | on | 0 | - | - | |
TroLase | black | Laser Engraving CO2 | 65 | 80 | 600 | 1 | off | 1.5 | bottom to top | - |
red | Laser Cutting CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - | |
TroGlass Reverse | black | Laser Engraving CO2 | 18 | 20 | 500 | 1 | on | 0 | bottom to top | - |
red | Laser Cutting CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - |
To attach the parts to each other, first remove the protective film on the back of the blue TroLase shield. Now stick the TroLase label onto the yellow TroLase or the white TroGlass Reverse label according to the markings.
The signs are now ready for use!
These signs can be produced in any colour material.