Tips and Tricks for Glass Engraving
Laser engraving is a quick and easy way to personalise wine glasses, beer mugs, vases, bottles, or carafes. Here are some useful tips and hints for glass processing.
What glass can be laser engraved?
With a CO2 laser engraving machine, you can laser engrave flat materials such as window glass or mirrors, round workpieces such as wine or champagne glasses, and conical items like bottles.
Cheaper, cast glasses are a good choice because they generally have lower lead content and are more homogeneous structure. Expensive, hand-blown glasses or crystal glasses may have stresses in the material that are aggravated by the heat during laser engraving, which may cause the glass to fracture.
You can also laser process mirror glass with a fiber laser by removing only the reflective layer on the back so that the glass itself is not engraved by the fiber laser, leaving the surface smooth.
The Trotec Speedy flexx has both a CO2 and a fiber laser source. Thus, you can easily combine both processing options with a single laser machine.
What processing options are there?
There are a number of methods for laser engraving glass and creating special effects. Here are few:
1. Moist paper towel
Using a moist paper towel helps prevent the engraving area from becoming rough, and leads to a clear, white engraving result.
Before you start engraving, apply a moist single-layer paper towel to the glass. Make sure there are no air bubbles or overlaps as this will affect the engraved image. Then switch the Air Assist to OFF to avoid premature drying of the paper during engraving. After engraving, the residue easily wipes off, also cleaning the engraving area is cleaned.
2. Application tape
In addition to moist paper towels, application tape can also be used to prevent the surface from roughening. With application tape, however, the engraving colour is grayish rather than bright white.
As with the paper towel method, make sure that no air bubbles and overlaps are formed when you apply the tape. After engraving, clean the glass to remove any adhesive residue.
3. Engraving without auxiliary materials
Moist paper towel or application tape are not required for processing glass. You can create effects by making adjustments such as changing the colour in the graphic from 100% black to about 70% gray to minimise the effect of heat on large surface, to optimise engraving results. You can also go to the print settings, select the rasterisation type “Ordered Dithering," but keep the same parameters. Due to this change not quite as much heat enters the material; hence, the surface is not roughened as much.
How to engrave glasses with curves and handles?
Glasses with curves can be processed with the rotary engraving attachment. For detailed instructions, see Tips and Tricks Rotary Attachment.
Glasses with handles are also processed using the rotary engraving attachment . It is important to make sure that the glasses are accurately placed so that the handle is not rotated into the engraving field. First, move the Y axis (rotary motion) to the very top. Clamp the workpiece so that the handle is slightly above the laser beam. Since the workpiece is rotated backwards for the laser process, there is no risk of collision with the laser head. For all workpieces with handles, make sure that circumference of the glass is large enough to accommodate the length of the graphic. Otherwise the graphic will be placed too close to the handle. You can easily check the position in the JobControl® laser software by using the “What you see is what you get” function. (WYSIWYG)
How can I see where my graphic will be lasered?
You can see the exact position of your graphics in the JobControl® laser software, by using the “What you see is what you get” function (WYSIWYG) and the crosshairs. If you are using the crosshairs, simply move the Y axis in the target position for lasering. Then place the job on the plate to the crosshairs. By moving the Y axis again, you can check the dimension of the job on your workpiece and correct any faulty positions of the workpiece or the job.
Tip : Select the option "Minimise to Job Size” in the JobControl® Print window to help position the graphic on the workpeice.
How to get the best effect of photo laser engraving on glass
For photo engraving on glass, use grayscale matrix of 70% black. This causes less heat to be applied to the glass, and the result will be finer. We recommend using an average resolution of 500 dpi and using the rasterisation type “Ordered Dithering." This optimises the image data for the material.
Need more help?
Contact the Trotec service hotline where top qualified and motivated laser experts will assist you with any questions or problems.