See our lasers in action!
Laser engraver and cutter
Speedy series: laser engraving and cutting machines for workpieces up to 40 x 24 inches
| ⚫ Engrave | ⚫ Cut | ⚫ Mark |
| Laser type: | CO₂, Flexx or Fiber laser |
|---|---|
| Work area: | 24.0 x 12.0 up to 40.0 x 24.0 inch |
| Max. workpiece height: | 4.9 - 12.0 inch |
| Laser power: | 20 - 120 watts |
Large-format laser cutter
SP series: CO2 laser cutter for large-format materials.
| ⚫ Engrave | ⚫ Cut | ⎯ Mark |
| Laser type: | CO₂ laser |
|---|---|
| Work area: | 49.0 x 28.0 up to 87.0 x 126.4 inch |
| Max. workpiece height: | 2.0 - 4.4 inch |
| Laser power: | 40 - 400 watts |
Industrial marking laser
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
| ⚫ Engrave | ⎯ Cut | ⚫ Mark |
| Laser type: | CO₂ or Fiber laser |
|---|---|
| Max. work area: | 7.5 x 7.5 up to 51.2 x 17.7 inch |
| Max. workpiece height: | 9.8 - 30.1 inch |
| Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Lasermade Jewelry
Necklace with Laser-Cut Pendant
Create a jewelry pendant as individual as its wearer
This pendant is made of 13 laser cut and engraved pieces. The exact measurements of the cutting gaps guarantees a firm hold without glue and engravings allow countless designs.
Preparation
Required material
- TroLase Reverse gloss/gold 1/16"
- Waxed cord or a ribbon
Trotec laser used
- Speedy 360
- 60 watts
- 1.5 inch lens
Tips:
Use a honeycomb cutting table or an acrylic cutting grid table to avoid back reflections
Step by Step
Step 1: Design
Open the PDF template and send the design to the laser or create your own design and add a personal touch to the pendant.
Do you want to use a different material?
Note that the cutting gap has been optimized for TroLase Reverse 1/16". When using other materials it may be necessary to adapt parameters and geometries.
Step 2: Laser Parameters
We used a Speedy 360 (60 watts power) to cut and engrave the material. We've sent the graphics with 600 dpi to the laser and used the following parameters:
Laser Settings
Engraving: Power: 100% - Speed: 60% - Frequency: 1000 ppi - Air Assist: On -
Z-Offset: 2.5mm
Cutting: Power: 50% - Speed: 0.6% - Frequency: 2000 Hz - Air Asisst: On
Additionally, we activated the optimized geometries function to achieve even higher quality.
Step 3: Cleaning and assembling
It may be necessary to clean the pieces and remove dust with a soft cloth. After that you can easily put the pieces together. There is no glue needed, because the pieces fit together perfectly.
Tip:
To cut out the stand, you can also use our template.
Step 4: Attach the ribbon
To assemble the piece of jewelry, take the small disk with the hole, pull the ribbon through and fix it with a knot. Cut the excess from the ends with scissors.
In the pictures below we have omitted the ribbon, so you can see the assembly better.
Step 5: First side part
Now insert one side part of the disc.
Step 6: Insert discs
Attach all other disks to the side part and pay attention to the order.
Step 7: Other side parts
As a final step, put the other side parts around and the necklace is ready to use.