--------------------------
acrylic-wood-memo-matching-game

Print & Cut memo matching game

Step by step instructions

acrylic-wood-memo-matching-game

Print & Cut memo matching game

Step by step instructions

Do you need promotional giveaways or gifts that can be adapted to your customers' needs? Then this printed matching game is for you.

Preparation

Required material
  • 2 sheets MDF 23.5" x 11.75", 1/4"
  • 1/4 sheet TroGlass Clear, 10mm
  • Material for covering the engraving table
Machine used
  • Speedy 360, 100 Watts
  • 2.5" lens
  • JobControl® Vision camera system
  • Aluminum cutting grid table or honeycomb cutting table for cutting the MDF
  • Acrylic cutting grid for cutting the acrylic

Any laser machine from the Speedy 300 platform or larger with JobControl® Vision software can create this sample.

Important

The option "Send Beziers and paths to driver" must be active in your program. Otherwise, JobControl® Vision will not recognize the registration marks.

graphics-files-matching-game.zip

ZIP

Download now

Step by step

design-memo-matching-game
Step 1

Step 1: Picture cards

Create your own designs or use ours. Add you or your customer's images in place of our own, then print the design directly to the MDF using a UV printer.
(See tips on graphics creation for JobControl® Vision)

Send the job to your laser with the below settings. Please do not deviate from these settings, or else JobControl® Vision will fail to recognize the registration marks.

Print settings:

Process mode Resolution Cut line
Cut Job 1000 dpi none
Halftone Others
Color enhanced geometries, inner geometries first
laser-cutting-acrylics-matching-game
Step 2

Step 2: Laser process picture cards

Set the parameters using the below settings. Based on your laser machine, the laser power available and the printing process used, the recommended settings may differ.

Instructions for using the JobControl® Vision software can be found here: JobControl® Vision software

Important: When cutting wood, a nozzle with a small diameter should be used. Additionally, the pressure of your air assist may be increased.

Tip: Lower any traces of smoke by applying application tape to the surface. Omit the registration marks so that the JobControl® Vision camera system may "read" them.

LASER PARAMETERS REGISTRATION MARKS:

Color Process Power (%) Speed (%) ppi/Hz
black RegMark - - -
Passes Air Assist Z-Offset Advanced
- - - -

LASER PARAMETERS CUTTING:

Color Process Power (%) Speed (%) ppi/Hz
red Cut CO2 90 0.6 1000
Passes Air Assist Z-Offset Advanced
1 on   -

TIP:

  • We used the standard laser parameters from JobControl®, optimized for quality
  • Material parameters for JobControl® can be obtained from www.troteclaser.com
print-settings-matching-game
Step 3

Step 3: Acrylic holder

Now we create an acrylic holder to put the picture cards inside.

Tip: Check the kerf when making the base plate and tweak it if required.

Send the job to the laser using the below settings.

Print settings:

Process mode Resolution Cut line
Cut Job 500 dpi -
Halftone Others
- enhanced geometries, inner geometries first
TroGlass-laser-cutting-matching-game
Step 4

Step 4: Laser process acrylic holder

Send the following parameter settings to your laser. These may change based on your laser machine and the laser power that's available.

Important: When cutting acrylic, a nozzle with a big diameter should be used. Additionally, the pressure of your air assist may be increased.

While cutting, the pole may bend.

LASER PARAMETER CUTTING:

Color Process Power (%) Speed (%) ppi/Hz
red Cut CO2 95 0.1 20000
Passes Air Assist Z-Offset Advanced
1 on -3 mm -

TIP:

  • We use the standard laser parameters in JobControl®, optimized for quality
  • Material settings for JobControl® can be obtained from www.troteclaser.com
assembly-matching-game
Step 5

Step 5: Finishing

After smoothing out the cut edges of the MDF cards, put the stand together.

Now your memo matching game with holder is finished.

Inspiration

  • Give your creativity free reign: Edit the shape of the cards, use a different material, add logos or other text to the back of the cards.
  • We engraved a stripe pattern into the card edges to create an elegant effect. This was achieved easily by placing the cards within the holder, putting them inside the laser and engraving each side.

Speedy series
The ideal laser engraver and cutter for personalization.

Discover laser engravers and cutters

Questions about applications or settings?
We're happy to advise you from A for Air assist to Z for z-offset.

Contact us
Proud member of troGROUP Logo