See our lasers in action!
Laser engraver and cutter
Speedy series: laser engraving and cutting machines for workpieces up to 40 x 24 inches
| ⚫ Engrave | ⚫ Cut | ⚫ Mark |
| Laser type: | CO₂, Fiber or Flexx laser |
|---|---|
| Work area: | 24.0 x 12.0 up to 40.0 x 24.0 inch |
| Max. workpiece height: | 4.9 - 12.0 inch |
| Laser power: | 10 - 120 watts |
Large-format laser cutter
SP series: CO2 laser cutter for large-format materials.
| ⚫ Engrave | ⚫ Cut | ⎯ Mark |
| Laser type: | CO₂ laser |
|---|---|
| Work area: | 49.0 x 28.0 up to 128.0 x 126.4 inch |
| Max. workpiece height: | 2.0 - 4.4 inch |
| Laser power: | 40 - 400 watts |
Industrial marking laser
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
| ⚫ Engrave | ⎯ Cut | ⚫ Mark |
| Laser type: | CO₂ or Fiber laser |
|---|---|
| Max. work area: | 7.5 x 7.5 up to 51.2 x 17.7 inch |
| Max. workpiece height: | 9.8 - 30.1 inch |
| Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Table decoration vintage style
Learn from this DIY tutorial how you can make a vintage themed table decoration with jute fabric and fusible interfacing.
Preparation
Required material:
- Jute fabric by the meter of cut, approx. 40 x 50 cm
- fusible interfacing D24 H200, approx. 35 x 35 cm
- Iron or press
Machine used:
- Speedy 360
- 80 watts
- 2" lens
- Nozzle with large diameter
- Vacuum table with honeycomb cutting table
This tutorial can be performed with any other Speedy laser engraver.
Important:
Maximize the vacuum by shutting the throttle valve.
Step by Step
Step 1: Jute fabric
Design your own pattern or use the template we provide. Send it to your laser with the below printer settings:
| Process mode | Resolution | Cut line |
|---|---|---|
| Standard | 500 dpi | None |
| Halftone | Others |
|---|---|
| Color | Optimized geometries inner geometries first |
Step 2: Laser process jute fabric
Set the parameters. The parameters we provide may change depending on the machine you are using and the laser power that you have available.
Tip: Before you engrave, iron the jute. You will obtain a nicer product if your material is extremely flat.
| Color | Process | Power (%) | Speed (%) | ppi/Hz |
|---|---|---|---|---|
| Black | Engrave CO2 | 75 | 80 | 500 |
| Red (scratching) | Cut CO2 | 13 | 1 | 1000 |
| Blue | Cut CO2 | 50 | 1.5 | 1000 |
| Color | Passes | Air Assist | Z-Offset | Advanced |
|---|---|---|---|---|
| Black | 1 | on | 20mm | - |
| Red (scratching) | 1 | on | 10mm | 1 |
| Blue | 1 | on | - | - |
Step 3: Fusible interfacing
Either design your own graphic or use our files. Send it to the laser with the below print settings:
| Process mode | Resolution | Cut line |
|---|---|---|
| Standard | 333 dpi | None |
| Halftone | Others |
|---|---|
| Ordered Dithering | Optimized geometries |
Step 4: Laser process Fusible interfacing
Set the parameters. The parameters we provide may change depending on the machine you are using and the laser power that you have available.
Tip: Be sure that it's the non-sticky front side of the fusible interfacing that you're engraving.
| Color | Process | Power (%) | Speed (%) | ppi/Hz |
|---|---|---|---|---|
| Black | Engrave CO2 | 50 | 100 | 500 |
| Red | Cut CO2 | 15 | 2 | 1000 |
| Color | Passes | Air Assist | Z-Offset | Advanced |
|---|---|---|---|---|
| Black | 1 | On | - | Optimized quality, correction 15 |
| Red | 1 | On | - | - |
Step 5: Finishing
Attach the fusible interfacing to the jute fabric with an iron or a press. Position the lace design onto the jute and press it into the material.
Settings:
Iron: Medium heat (level 2), 8 seconds
Press: 130 - 165°C, 8 seconds
Important: Place a piece of fabric onto the interfacing before ironing or pressing. This will prevent it from melting and sticking to the hot surface.
If you would rather your decoration have a more rustic look, remove individual threads from the jute to make fringes.
Downloads
Trotec Product Recommendations
X 
