See our lasers in action!
Laser engraver and cutter
Speedy series: laser engraving and cutting machines for workpieces up to 40 x 24 inches
| ⚫ Engrave | ⚫ Cut | ⚫ Mark |
| Laser type: | CO₂, Flexx or Fiber laser |
|---|---|
| Work area: | 24.0 x 12.0 up to 40.0 x 24.0 inch |
| Max. workpiece height: | 4.9 - 12.0 inch |
| Laser power: | 20 - 120 watts |
Large-format laser cutter
SP series: CO2 laser cutter for large-format materials.
| ⚫ Engrave | ⚫ Cut | ⎯ Mark |
| Laser type: | CO₂ laser |
|---|---|
| Work area: | 49.0 x 28.0 up to 87.0 x 126.4 inch |
| Max. workpiece height: | 2.0 - 4.4 inch |
| Laser power: | 40 - 400 watts |
Industrial marking laser
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
| ⚫ Engrave | ⎯ Cut | ⚫ Mark |
| Laser type: | CO₂ or Fiber laser |
|---|---|
| Max. work area: | 7.5 x 7.5 up to 51.2 x 17.7 inch |
| Max. workpiece height: | 9.8 - 30.1 inch |
| Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Felt quiver
Step by step guide
Lasercut and engrave your individual quiver out of felt and wood, and let your arrows hit the bullseye.
Preparation
Required material:
- 1/8" Polyester felt in any colour
- 1/8" Alder solid wood
- Wool in any colour
- Sticky tape
Used Trotec Laser:
- Speedy 400
- 80 watts
- 2.0 inch lens
Tip:
Vacuum table with honeycomb cutting tabletop or aluminum cutting grid table
Step by Step
Step 1: Design
Import the PDF file into Corel Draw and select your desired model and the design for either felt or wood (see the tabs below the working area in Corel Draw).
Step 2: Laser parameters
Felt:
Engraving: Power: 33% - Speed: 50% - Frequency: 500ppi - Air Assist: ON
- Advanced: Optimized Quality
Cutting: Power: 40% - Speed: 2% - Frequency: 1000Hz - Air Assist: ON
Wood:
Engraving: Power: 60% - Speed: 50% - Frequency: 500ppi - Air Assist: ON
Cutting: Power: 100% - Speed: 1.8% - Frequency: 1000Hz - Air Assist: ON
Step 3: Laser cut and engrave felt and wood
Before you begin with the cutting and engraving process, be sure to cover the cutting table around the felt with cardboard and sticky tape. This way the felt is properly fixed for laser cutting and engraving.
You can adjust the size of the felt in CorelDraw according to the length of the arrows you will be putting into your quiver. Our sample is best suited for very long arrows.
Send the file with the perfect size to your laser cutter. After you've taken the felt out of the laser, put your hardwood board inside. Now send the file for laser cutting and engraving the bottom part of the quiver to the laser.
Step 4: Sewing the pieces
Next you have to sew the round wooden plate and the felt along the holes together. Take the side with the pattern and sew it onto the wooden plate. Make sure the engraving will be on the outside. Sew the felt along the length and the remaining holes at the top together.
Our quiver is ready for your next archery training session!