Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Make a three-dimensional winners' trophy using Trotec materials and 3D relief laser engraving
You can use any other machine of the Speedy Flexx laser engraver series.
TroGlass Satins and TroGlass Metallic have a very high-end finish
You can make your own design or import our template and then adapt it to your requirements. We have engraved a recess out of the base plate to hold the TroGlass Metallic ring.
Process mode | Resolution | Cut line |
---|---|---|
Standard | 500dpi | none |
Halftone | Other |
---|---|
colour | Optimized geometries |
Put TroGlass Satin Black on the acrylic grid of your Trotec laser. Engrave and cut the base plate using the parameters below. The parameters can differ depending on the laser machine used and laser power available.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
black | Engrave CO2 | 40 | 10 | 500 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 2mm | - |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 8 | 0.8 | 5000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 1 mm | - |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
blue | Cut CO2 | 95 | 0.8 | 5000 |
Passes | Air Assist | Z-offset | Advanced |
---|---|---|---|
1 | on | - | - |
Send the job for the TroGlass Metallic ring to the laser using the driver settings below.
Process mode | Resolution | Cut line | Halftone | Others |
---|---|---|---|---|
Standard | 600dpi | none | - | - |
Put the TroGlass Metallic sheet on the acrylic cutting table and engrave the job using the parameters below:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
black | Engrave CO2 | 16 | 20 | 600 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 1 mm | - |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut Co2 | 50 | 0.2 | 5000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | - | - |
Tip: We used the JobControl® parameters for TroGlass optimized for quality.
Finally, send the files for 3-dimensional wood engravings and the other wooden parts to the laser:
Process mode | Resolution | Cut line | Halftone | Others |
---|---|---|---|---|
Standard | 500dpi | None | - | - |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Black | Engrave CO2 | 100 | 30 | 500 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
3 (!!) | On | - | - |
Color | Process | Power (%) | Speed (%) | ppi / Hz |
---|---|---|---|---|
Red | Cut CO2 | 100 | 1 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | On | - | - |
Tip:
When engraving deeply into wood, it can be helpful to cut the job first and engrave the job afterwards.
Clean the two acrylic pieces with a damp cloth. The wood relief engraving can be cleaned best with some water and a tooth brush. Here you can find tips for correct cleaning.
Put the acrylic glue on the engraved ring of the base plate and position the TroGlass Metallic ring on it. Press down firmly and allow the glue to cure.
Put double-sided adhesive tape or dots where the wooden relief shall be positioned and fix it.
Take the wooden spacer and apply double-sided adhesive tape on both sides. Position it on the left and the right of the black base plate. Make sure to have a rectangular contact surface so that the trophy stands upright.
Finally, fix the lettering "winner" and the corresponding back on the spacers to complete this elegant trophy.
Combine other types of solid wood and TroGlass materials to adapt the trophy to your customers' requirements.