Atmos Laser Exhaust Systems

Exhaust systems for Trotec laser machines

The Atmos laser exhaust system ensures safe and clean operation of your laser system. It removes dust and gas from processing space and filters odors that occur during laser processing through its activated carbon filters. With this the Atmos laser exhaust system facilitates the best possible laser engraving and laser cutting quality.

With Atmos, Trotec sets standards in userfriendliness, efficiency and low laser maintenance costs.


For each application the appropriate laser exhaust system

Choosing the right exhaust system guarantees a long operation life for your laser equipment. The Atmos exhaust systems are optimally integrated with Trotec laser systems.

Atmos Nano

Atmos Nano

Compact and easy to transport, ideal for fiber laser applications with particularly small dust particles and minimal odor.

Atmos Compact

Atmos Compact

Forms a single unit with smaller laser devices and simultaneously functions as a support frame, suitable for applications with low level of dust.

Atmos Mono

Atmos Mono

Stand-alone version with one turbine for applications with medium levels of dust.

​Atmos Mono Plus

Atmos Mono Plus

Stand-alone version with one turbine and two activated carbon Comfort Bags, perfect for odor-intensive applications and medium levels of dust.

​Atmos Duo Plus

Atmos Duo Plus

Stand-alone version with two turbines and two activated carbon Comfort Bags, perfect for odor-intensive applications and high levels of dust.

* Without vacuum table
** Without table exhaust


Atmos Pre-filters for high-dust laser engraving and laser cutting applications

The use of a pre-filter is recommended in cases when engraving and cutting of materials produce a large amount of dust, such as e.g. wood or stamp rubber. The pre-filter is positioned between the laser machine and the exhaust system. It ensures that coarse particles and dust are separated from the exhaust air before entering the filter of the laser exhaust system. This increases the service life of your exhaust system significantly and reduces costs for replacement filters.

If particularly tenacious particles are produced, (e.g.when processing acrylic), the pre-filter can be equipped with an additive dosage unit to prolong the service life of the filter.

VENT exhaust fan for efficient removal of gas and dust

Vent series fans ensure efficient removal of dust and gases that do not require filtering. If you opt for this exhaust system, please keep in mind that it will not clean dust particles or filter odors. Should a filtering exhaust system be required at a later stage, we offer suitable exhaust systems that include a filter from the Atmos series.

The fans are designed in aluminum silicon alloy cast or steel plate and therefore ensure long-term, robust and failure-free operation.

Atmos laser exhaust systems: intelligent, economical and clean

Automatic power control: The exhaust rate is adjusted fully automatically depending on the saturation of the filter. Gas and dust are optimally extracted for all applications at any time and a constant flow of air is guaranteed.

Bi-directional control: Atmos laser exhaust systems communicate with Trotec JobControl®, SpeedMark or DirectMark Software. The software starts automatically when the laser processing begins, and stops as soon as the job is finished. Processing notifications and warnings are displayed in the software.

Convenient filter exchange: Replacement of filter units and activated carbon is easy, clean and convenient. The innovative design allows you to replace the entire filter on your exhaust system in just a few movements.

Digital control panel: The control panel can be accessed easily and conveniently at any time. Its display shows filter saturation, air flow, operating hours and speed range.

Economic operation: The Atmos laser exhaust systems are equipped with brushless continuous flow turbines. They are completely maintenance-free. In addition, the continuous fresh air cooling ensures maximum operating life.

Energy-saving mode: The Trotec JobControl® software can be used to set the running time of the turbines before and after completing the engraving process. The exhaust power is thus adjusted reliably and saves valuable energy and money by automated switch-on times.


Atmos laser exhaust systems: intelligent, economical and clean

Automatic power control

The exhaust rate is adjusted fully automatically depending on the saturation of the filter. Gas and dust are optimally extracted for all applications at any time and a constant flow of air is guaranteed.

Bi-directional control

Atmos laser exhaust systems communicate with Trotec JobControl®, SpeedMark or DirectMark Software. The software starts automatically when the laser processing begins, and stops as soon as the job is finished. Processing notifications and warnings are displayed in the software.

Convenient filter exchange

Replacement of filter units and activated carbon is easy, clean and convenient. The innovative design allows you to replace the entire filter on your exhaust system in just a few movements.

Digital control panel

The control panel can be accessed easily and conveniently at any time. Its display shows filter saturation, air flow, operating hours and speed range.

Economic operation

The Atmos laser exhaust systems are equipped with brushless continuous flow turbines. They are completely maintenance-free. In addition, the continuous fresh air cooling ensures maximum operating life.

Energy-saving mode

The Trotec JobControl® software can be used to set the running time of the turbines before and after completing the engraving process. The exhaust power is thus adjusted reliably and saves valuable energy and money by automated switch-on times.

Options for the Atmos laser exhaust systems

Cleaning set

Helps to clean the inside of your laser and the workpieces. The cleaning set can also be attached to the exhaust hose on the back of the Atmos exhaust system.

Sound insulation module

Ensures the further reduction of operating noise and makes the Atmos exhaust systems even more quiet. Ideal for the use in offices or retail locations.

Replacement filter

The user can choose between the standard filter or the HEPA filter. The standard filter is the ideal choice for all CO2 and flexx applications, the HEPA filter is particularly suited to fiber laser applications with the smallest dust particles. It is easy to replace the particle filter: Open the lid, remove the filter and insert the new filter. The layer structure of the filter and the use of pre-filter matting results in cost savings.

"Comfort Carbon" activated carbon filter

Maximum filtering of odors using highly efficient activated carbon.

Exhaust connection

All stand-alone devices in the Atmos Series can be connected to an external exhaust system.

Pre-filter systems

The use of pre-filter is recommended, if there is a large quantity of dust to be filtered. This is positioned between the laser device and the exhaust system. The dust particles are collected in a separate container. You can choose between pre-filter systems with mechanical or automatic cleaning (using compressed air). If particularly tenacious particles are produced (e.g. when processing acrylic), the pre-filter can also be equipped with an optional additive dosage unit.

Atmos Product Guide

  Atmos Nano
(highly compact)
Atmos Compact
(ride-on)
Atmos Mono
(stand-alone)
Atmos Mono Plus
(stand-alone)
Atmos Duo Plus
(stand-alone)
Dimensions
D x W x H mm
399 x 328 x 540 675 x 815 x 555/520 700 x 560 x 1050 700 x 560 x 1050 700 x 560 x 1050
Weight 32 kg 88 kg 104 kg 113 kg 115 kg
Energy supply 230V/50/60 Hz 115V/50/60 Hz 230V/50/60 Hz 115V/50/60 Hz 230V/50/60 Hz 115V/50/60 Hz 230V/50/60 Hz 115V/50/60 Hz 230V/50/60 Hz
Motor 1 pc. continuous
flow turbine
1 pc. continuous
flow turbine 
1 pc. continuous
flow turbine
1 pc. continuous
flow turbine
2 pcs. continuous
flow turbines
Performance 200 m³/h 250 m³/h 320 m³/h 320 m³/h 2 x 320 m³/h
Pressure increase 8,500 Pa (230V)
5,800 PA (115V)
8,500 Pa (230V)
5,800 PA (115V)
8,500 Pa (230V)
5,800 PA (115V)
8,500 Pa (230V)
5,800 PA (115V)
8,500 Pa (230V)
Filter type and equipment H13 combination filter and activated carbon Bag filter F9 and activated carbon Compact filter F9 and activated carbon or H13 combination filter and activated carbon Compact filter F9 and activated carbon or H13 combination filter and activated carbon Compact filter F9 and activated carbon or H13 combination filter and activated carbon

The use of a pre-filter is recommended, if there is a large quantity of dust to be filtered. We are happy to advise you.

Contact us