See our lasers in action!
Laser engraver and cutter
Speedy series: laser engraving and cutting machines for formats up to 40 x 24 inches
| ⚫ Engrave | ⚫ Cut | ⚫ Mark |
| Laser type: | CO₂, Flexx or Fiber laser |
|---|---|
| Work area: | 24.0 x 12.0 up to 40.0 x 24.0 inch |
| Max. workpiece height: | 4.9 - 12.0 inch |
| Laser power: | 20 - 120 watts |
Large-format laser cutter
SP series: CO2 laser cutter for large-format materials.
| ⚫ Engrave | ⚫ Cut | ⎯ Mark |
| Laser type: | CO₂ laser |
|---|---|
| Work area: | 49.0 x 28.0 up to 87.0 x 126.4 inch |
| Max. workpiece height: | 2.0 - 4.4 inch |
| Laser power: | 40 - 400 watts |
Industrial marking laser
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
| ⚫ Engrave | ⎯ Cut | ⚫ Mark |
| Laser type: | CO₂ or Fiber laser |
|---|---|
| Max. work area: | 7.5 x 7.5 up to 51.2 x 17.7 inch |
| Max. workpiece height: | 9.8 - 30.1 inch |
| Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
3D Wall Decoration: Elephant
Step-by-step tutorial
In only a few cuts you can create this three-dimensional elephant using TroCraft Eco laser material.
Preparation
Used material:
- 1 sheet TroCraft Eco plate thickness 1/16", 24" x 12"
- Material to cover the remainder of the working area
Two pieces of the elephant's head can be made from one sheet of TroCraft Eco.
Machine used:
- Speedy 360
- 120 watts
- 1.5" lens
- Aluminum cutting grid table or honeycomb cutting tabletop
Create this project using any model from the Speedy laser engraver series.
Downloads:
For a wall decoration of this design (width approx. 24") download the free, larger version of this file. This size will require 6 sheets of TroCraft Eco 24" x 12" each. Adjust the parameter settings according to the thickness of the material.
Step by Step
Step 1: Import your design
Create your own design or use our template. Send the job to the laser using the settings below.
Print settings:
| Process mode | Resolution | Cut line |
|---|---|---|
| Standard | 500 dpi | none |
| Halftone | Others |
|---|---|
| Ordered Dithering | optimized geometries, inner geometries first |
Step 2: Laser process TroCraft Eco
Enter the parameter settings. Our suggested parameters may vary depending on the laser machine used and the available laser power.
Place a sheet of TroCraft Eco into the laser, and cover the remaining work area to create a vacuum effect. Now you're ready to begin processing.
Laser Parameters:
| Color | Process | Power (%) | Speed (%) | ppi/Hz |
|---|---|---|---|---|
| Black | Engrave CO2 | 9 | 50 | 500 ppi |
| Red | Cut CO2 | 24 | 2 | 1000 Hz |
| Passes | Air Assist | Z-Offset | Direction | Advanced |
|---|---|---|---|---|
| 1 | ON | - | top down | High quality |
| 1 | ON | - | - | - |
Step 3: Assembly
After processing has completed, remove the pieces from the laser. Pieces are organized in size or sequence from bottom right to top left.
Take the largest piece of the elephant head (without ear cut-outs) and insert it into the rearmost slot of the grid elements. Proceed with the other pieces this way, working back to front. When you are finished, the smallest piece should be placed in the frontmost slot.
Finally, turn the elephant head over and slide the rectangular plate through the two slots. This keeps the pieces in place and serves as a suspension eyelet so that you can display your application.
TroCraft Eco – the laser material made of recyclable resources
Society continues to focus on sustainable and environmentally-friendly values, and therefore prefer materials that support these causes. TroCraft Eco is made from pure cellulose fiber, produced without additives, is fully biodegradable and is also emissions-free.