Create a board game
with your laser

Step by step guide

laser cutting board game

Priprema

Required material

board:
50 x 50 cm TroLase walnut/white1.6mm
Acrylic(red, blue, yellow, green) 0.8mm - adhesive tape on back side

figures:
Acrylic (red, blue, yellow, green) 3.2mm

stickers:
TroLase lights gold/black 0.1mm

Used Trotec Laser
  • Speedy 360
  • 80 watts
  • 2 inch lens
Tip

white acrylic grating

Detaljni vodič

laser engraved board game
Korak 1

Step 1: Board

First decide what size board you would like. We are using 50x50 cm pre-cut acrylic for our extra-large board game. Adapt the design as you wish and send the file to the laser.

Tip:

For the best results and less cleaning effort, the board should be engraved from bottom to top.

board game laser engraving
Korak 2

Step 2: Colorful dots for the starting area

Cut five circles per color from 0.8mm acrylic to indicate the players areas.
For best results, we recommend using the white acrylic-cutting-grid, leaving the protective foil on the material during the cutting process on the material.

You can order the acrylic with an adhesive film on the back and then you just have to put the circles on the appropriate places. Make sure the board is clean before you apply them.

play figure laser cut
Korak 3

Step 3: Figures

Now you need the red, blue, yellow and green acrylic (3.2 mm) for the figures. Cut out the characters and the matching discs (standing feet) per color and plug them together.
Again, it is important to leave the protective foil on the material during the cutting process for a brilliant cutting edge.

sticker laser cutting
Korak 4

Step 4: Decoration

We used some stickers to make the game board look less empty and more fun.

We engraved TroLase Lights and used our Kiss Cut parameters to "cut-in" the material. Only the adhesive film is cut and the support material remains unblemished. Then the sticker can be removed easily.

It is important to also engrave the stickers from the bottom to the top
(see step1).

board game laser cutting
Korak 5

Step 5: Used laser parameters

We worked with a Speedy 360 80 watts power and the parameters listed below. You can download the JobControl files and import them easily into your parameters database (see download area below). 

Board - TroLase 1,6 mm

Engraving: power: 80% - speed: 100% - frequency: 500 ppi - air assist: ON - Z-Offset: 1.5 mm
For best engraving results, we've activated the "high quality" function and set 1.5mm Z-Offset. 

Dots - Acrylic 0,8 mm

Cutting: power: 33% - speed: 1.2% - frequency: 1.000 Hz - air assist: ON

Figures - Acrylic 3,2 mm

Cutting: power: 45% - speed: 0.4% - frequency: 1.000 Hz - air assist: ON - 
Z-Offset: -0,6 mm
Here we also worked with 0.6mm Z-Offset for a smoother engraving.

Sticker - TroLase Lights 0,1 mmticker - troLase Lights 0,1 mm

Engraving: power: 35% - speed: 50% - frequency: 500 ppi - air assist: ON - Z-Offset: 2 mm
Cutting: power: 20% - speed: 2 % - frequency: 1.000 Hz - air assist: ON 
KissCut: power: 8% - speed: 2% - frequency: 1.000 Hz - air assist: ON
We also recommend that you activate the "high quality" function. The laser process takes more time, but the perfect result is worth it.

Serija Speedy
Idealan laserski graver i sekač za personalizaciju.

Otkrijte laserske gravere i sekače

Da li imate pitanja o aplikacijama ili podešavanjima?
Drago nam je što možemo da vam pružimo detaljne savete, od Air Assist-a do z-pomaka.

Kontaktirajte nas
Ponosni član troGROUP Logo