Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Step-by-Step instruction
Create these wall stickers using different colors of TroLase Thins.
If you want to make the wall stickers with another machine of the Speedy series, please consider the size of the motive. If necessary, the pattern must be scaled accordingly, which may also require a corresponding adjustment of the cutting parameters.
The specified parameters refer to the butterfly in large format (engravings in grayscale, cutting lines in red). The duration for cutting the large motif is only approx. 3 min, the engraving duration is approx. 35 min. If you want to keep the production time of the wall sticker as short as possible, you can hide the pre-meter settings for the engraving color black. Only the red cutting lines are executed, the time-consuming engravings are omitted. In order to make the best possible use of the large format of the material, you can add 6 smaller butterflies (level 2, blue lines) to the template. Then adjust the parameter settings for the blue cutting lines according to your quality requirements. If you prefer a full-surface gluing of the wall sticker, you can also order the TroLase Thins with self-adhesive foil on the back.
Create your own design or use our template. Now send the job to the laser with the settings below.
Process | Resolution | Cutting line |
---|---|---|
Relief | 500dpi | none |
Raster | Other |
---|---|
- | Optimized geometries, inner geometries first |
Now make the parameter settings. Our suggested parameters may vary depending on the laser machine used and the available laser power. Remove the protective film from the surface of the TroLase Thin and then place the material - with the gold side up - on the aluminum grid table in your laser. Tape the remaining narrow edge to create the best possible vacuum.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Black | Engraving CO2 | 40 | 65 | 500 |
Red | Cutting CO2 | 30 | 3.2 | 1000 |
Passes | Air assist | Z-Offset | direction | Path planning | Advanced |
---|---|---|---|---|---|
1 | ON | +1 | bottom to top | - | optimized quality, correction: 5 |
1 | ON | - | - | throughput | correction: 5 |
After the laser, take the butterfly out of the laser machine. To remove the dust, carefully clean the wall sticker with a soft, damp cloth. Then glue some pieces of the double-sided adhesive tape onto the back of the wall sticker. Design the decoration according to your wishes
Execute the wall sticker also in other colors of the TroLase Thins. Depending on the color of the material, adjust the parameter settings to suit your requirements.
Combine the different butterflies to create an attractive wall decoration.