See our lasers in action!
Laser engraver and cutter
Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
| ⚫ Engrave | ⚫ Cut | ⚫ Mark |
| Laser type: | CO₂, Fiber or Flexx laser |
|---|---|
| Work area: | 610 x 305 up to 1016 x 610 mm |
| Max. workpiece height: | 125 - 305 mm |
| Laser power: | 20 - 120 watts |
Large-format laser cutter
SP series: CO2 laser cutter for large-format materials.
| ⚫ Engrave | ⚫ Cut | ⎯ Mark |
| Laser type: | CO₂ laser |
|---|---|
| Work area: | 1245 x 710 up to 3250 x 3210 mm |
| Max. workpiece height: | 50 - 112 mm |
| Laser power: | 40 - 400 watts |
Industrial marking laser
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
| ⚫ Engrave | ⎯ Cut | ⚫ Mark |
| Laser type: | CO₂ or Fiber laser |
|---|---|
| Max. work area: | 190 x 190 up to 1300 x 450 mm |
| Max. workpiece height: | 250 - 764 mm |
| Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Table decoration vintage style
See in this DIY sample how you can create a table decoration in vintage style using jute fabric and fusible interfacing.
Preparation
Required material:
- Jute fabric by the meter of cut, approx. 40 x 50 cm
- fusible interfacing D24 H200, approx. 35 x 35 cm
- Iron or press
Machine used:
- Speedy 360
- 80 watts
- 2" lens
- Nozzle with large diameter
- Vacuum table with honeycomb cutting table
This sample can be produced with any other machine of the Speedy laser engraver series.
Important:
Close the throttle valve to maximize the vacuum.
Step by Step
Step 1: Jute fabric
Make your design or use our template. Send it to the laser using the following print settings:
| Process mode | Resolution | Cut line |
|---|---|---|
| Standard | 500 dpi | None |
| Halftone | Others |
|---|---|
| Color | Optimized geometries inner geometries first |
Step 2: Laser process jute fabric
Make the parameter settings. Our parameters can differ depending on the machine used and laser power available.
Tip: Iron the jute before engraving. You get better results if the material is very flat.
| Color | Process | Power (%) | Speed (%) | ppi/Hz |
|---|---|---|---|---|
| Black | Engrave CO2 | 75 | 80 | 500 |
| Red (scratching) | Cut CO2 | 13 | 1 | 1000 |
| Blue | Cut CO2 | 50 | 1.5 | 1000 |
| Color | Passes | Air Assist | Z-Offset | Advanced |
|---|---|---|---|---|
| Black | 1 | on | 20mm | - |
| Red (scratching) | 1 | on | 10mm | 1 |
| Blue | 1 | on | - | - |
Step 3: Fusible interfacing
Make your design or use our template. Send it to the laser using the following print settings:
| Process mode | Resolution | Cut line |
|---|---|---|
| Standard | 333 dpi | None |
| Halftone | Others |
|---|---|
| Ordered Dithering | Optimized geometries |
Step 4: Laser process Fusible interfacing
Make the parameter settings. Our parameters can differ depending on the machine used and laser power available.
Tip: Make sure that you engrave on the front of the material (non-sticky).
| Color | Process | Power (%) | Speed (%) | ppi/Hz |
|---|---|---|---|---|
| Black | Engrave CO2 | 50 | 100 | 500 |
| Red | Cut CO2 | 15 | 2 | 1000 |
| Color | Passes | Air Assist | Z-Offset | Advanced |
|---|---|---|---|---|
| Black | 1 | On | - | Optimized quality, correction 15 |
| Red | 1 | On | - | - |
Step 5: Finishing
Fix the fusible interfacing on the jute fabric. Use either an iron or a press. Position the lace design on the jute and press or iron it.
Settings:
Iron: Medium heat (level 2), 8 seconds
Press: 130 - 165°C, 8 seconds
Important: Put a piece of fabric on the interfacing before you iron or press it. This prevents the material from eventually stick on the hot surface.
If you want to have your table decoration more country style, you can remove single jute threads and create fringes.
Downloads
Trotec Product Recommendations
X 
