Trophy with relief engraving

Make a three-dimensional winners' trophy using Trotec materials and 3D relief laser engraving

laser-engraving-relief-trophy

Preparation

Required material
Machine used
  • Speedy 360 flexx
  • 80 watts
  • 2" lens
  • Vacuum table with honeycomb cutting table resp. acrylic grid

You can use any other machine of the Speedy Flexx laser engraver series.

Tip

TroGlass Satins and TroGlass Metallic have a very high-end finish

Balloon Trophy

ZIP

Download now

Step by step

Druckereinstellungen TroGlass Satins
Step 1

Design

Import our template and adapt it to your requirements.

With "Create job" move the design to the "Prepare" screen. 

Step 2

Laser process TroGlass Satins Black

Place the job to the desired position and adapt the settings.

The laser parameters may vary depending on the type of laser machine and available laser power.

Send the job to the "Queue" for Laser processing.

Effect Engrave Quality
Process Engrave
Layers black
Power (%) 40
Speed (%) 10
DPI 500
Source CO2
Air Assist On
Z-offset 2mm
Passes 1
Power Correction 20
Direction Bottom up
Dithering None
Engraving Mode Standard
Effect Cut Quality
Process Cut
Layers blue
Power (%) 100
Speed (%) 1.2
Hz 5000
Source CO2
Air Assist On
Z-offset 0
Passes 1
Power Correction 7
Path planning Standard
Effect Cut Quality
Process Cut
Layers red
Power (%) 8
Speed (%) 0,8
Hz 5000
Source CO2
Air Assist On
Z-offset 1 mm
Passes 1
Power Correction -
Path planning Standard
Step 3

Step 3: Laser process TroGlass Metallic

Place the job to the desired position and adapt the settings.

The laser parameters may vary depending on the type of laser machine and available laser power.

Send the job to the "Queue" for Laser processing.
 

Effect Engrave Quality
Process Engrave
Layers black
Power (%) 16
Speed (%) 20
DPI -
Source CO2
Air Assist On
Z-offset -
Passes 1
Power Correction -
Direction Bottom up
Dithering None
Engraving Mode Standard
Effect Cut Quality
Process Cut
Layers red
Power (%) 50
Speed (%) 0.2
Hz 5000
Source CO2
Air Assist On
Z-offset -
Passes 1
Power Correction -
Path planning Standard
relief-engraving-wood
Step 4

Laser process Solid Wood Maple

Place the job to the desired position and adapt the settings.

The laser parameters may vary depending on the type of laser machine and available laser power.

Send the job to the "Queue" for Laser processing.
 

Effect Engrave Quality
Process Engrave
Layers black
Power (%) 100
Speed (%) 30
DPI 500
Source CO2
Air Assist On
Z-offset -
Passes 3
Power Correction 20
Direction Bottom up
Dithering None
Engraving Mode Relief
Effect Cut Quality
Process Cut
Layers red
Power (%) 100
Speed (%) 1
Hz 1000
Source CO2
Air Assist On
Z-offset -
Passes 1
Power Correction -
Path planning Standard
Step 5

Finishing

Clean the two acrylic pieces with a damp cloth. The wood relief engraving can be cleaned best with some water and a tooth brush. Here you can find tips for correct cleaning.

Put the acrylic glue on the engraved ring of the base plate and position the TroGlass Metallic ring on it. Press down firmly and allow the glue to cure.
Put double-sided adhesive tape or dots where the wooden relief shall be positioned and fix it.

Take the wooden spacer and apply double-sided adhesive tape on both sides. Position it on the left and the right of the black base plate. Make sure to have a rectangular contact surface so that the trophy stands upright.

Finally, fix the lettering "winner" and the corresponding back on the spacers to complete this elegant trophy.

trotec-inspiration-trophy

Inspiration

Combine other types of solid wood and TroGlass materials to adapt the trophy to your customers' requirements.

Speedy series
The ideal laser engraver and cutter for personalization.

Discover laser engravers and cutters

Questions about applications or settings?
We're happy to advise you from A for Air assist to Z for z-offset.

Contact us
Proud member of troGROUP Logo