--------------------------
Inspiration lasercut Mother's Day bouquet

Decorative Mother's Day bouquet made of TroGlass and wood veneer

Learn how you can produce a decorative and extraordinary Mother's Day gift.

Preparation

Required material

optional:

  • hot air gun
  • bench vice
  • work gloves
Machine used
  • Speedy 400 flexx, 100 watts
  • 2" lens or 2.5" lens for TroGlass Clear 10mm
  • vacuum table with honeycomb cutting table resp. acrylic grid

For this sample you can use any laser machine from the Speedy laser engraver series.

Tip

You can use leftover material for the "blossoms."

flowerbouquet-mothersday.zip

ZIP

Download now

Step by step

Printer settings TroGlass Clear 10mm
Step 1

Step 1: Import design

Make your own design or import our template. Adapt it to your requirements. Send the job for laser cuttting the base plate to the laser using the driver settings below.

Print settings:

Process mode Resolution Cut line
Cut Job 1000 dpi none
Halftone Others
Color Optimized geometries, inner geometries first
Laser cutting base plate
Step 2

Step 2: Cutting base plate

Put the TroGlass Clear on the acrylic cutting grid of your Trotec laser and insert the 2.5" lens. Then cut the base using the following settings. The parameters can differ depending on the laser machine used and laser power available.

Laser Parameters Cutting

Color Process Power (%) Speed (%) ppi/Hz
red Cut CO2 95 0.2 20000
Passes Air Assist Z-Offset Advanced
1 on -3 mm -

Info:

We used the standard parameters TroGlass Clear (speed optimized) from JobControl® .

printer settings TroGlass 3mm
Step 3

Step 3: Design "grass"

Send the design for the grass to the laser using the settings below.

Print settings:

Process mode Resolution Cut line
Standard 500 dpi none
Halftone Others
Color Optimized geometries
TroGlass Color Gloss laser process
Step 4

Step 4: Laser process "grass"

Put the dark green transparent TroGlass onto the acrylic cutting grid of your Trotec laser. Use the 2" lens for this and all following tasks for this application. Engrave and cut the design with the following parameters. The parameters can differ depending on the laser machine used and laser power available.

Laser parameters

Process Color Process Power (%) Speed (%)
Engraving black Engrave CO2 14 20
Cutting red Cut CO2 100 1
ppi/Hz Passes Air Assist Z-Offset Advanced
500 1 on 0mm High Quality
1000 1 on - -

Tip:

Start the engraving process from the bottom so that the dust cannot settle on the engraved area.

printer settings solid wood
Step 5

Step 5: Design "Stem"

The next step is to send the design of the solid wood stem to the laser using the driver settings below.

Print settings:

Process mode Resolution Cut line
Cut Job 1000 dpi none
Halftone Others
- Optimized geometries
Laser process solid wood
Step 6

Step 6: Laser process "Stem"

Change the acrylic cutting grid against the honeycomb cutting table and position the walnut sheet. Cover the rest of the engraving area to maximize vacuum. Cut the material using the parameters below:

Laser Paramters Cutting

Color Process Power (%) Speed (%) ppi/Hz
red Cut CO2 100 1 1000
Passes Air Assist Z-Offset Advanced
1 on - -

Tip:

By covering the engraving area, you produce a vacuum which is essential for a clean and consistent cut.

printer settings wood veneer
Step 7

Step 7: Design "Blossoms"

Finally, send the design of the abstract blossoms to your laser.

Print settings:

Process mode Resolution Cut line
Cut Job 1000 dpi none
Halftone Others
- Optimized Geometries, Inner Geometries first
laser cutting wood veneer
Step 8

Step 8: Laser process "Blossoms"

Put the maple veneer sheet into the laser, and carefully cover the rest of the engraving table. Then cut the blossoms using the following parameters:

Laser Parameters Cutting

Color Process Power (%) Speed (%) ppi/Hz
red Cut CO2 100 1.2 1000
Passes Air Assist Z-Offset Advanced
1 on - -

Tip:

If you cut the entire sheet, focus on the middle of the material to compensate for any differences in thickness.

assembly wood acrylic bouquet
Step 9

Step 9: Assembly

Put the stem into the base and decorate it with the blossoms. You can combine large and small blossoms. Finally, position the grass into the base, and this inventive Mother's Day bouquet is ready.

Handicraft tip:

Twisted blades of grass are an additional eye catcher. To make these, position the "blades of grass" into a bench vice or another heat-resistant holder. Take a hot air gun and carefully heat the filigree grass. Then deform and twist the hot acrylic. Don't forget to wear gloves! Hold the acrylic in place until it is cooled down. With a little practice, you can get impressive objects.

Inspiration lasercut Mother's Day bouquet

Inspiration

Use other colors of TroGlass Satins and transform the "flower bouquet" into an abstract sculpture.

Speedy series
The ideal laser engraver and cutter for personalization.

Discover laser engravers and cutters

Questions about applications or settings?
We're happy to advise you from A for Air assist to Z for z-offset.

Contact us
Proud member of troGROUP Logo