Decorative Mother's Day bouquet made of TroGlass and wood veneer

Learn how you can produce a decorative and extraordinary Mother's Day gift.

Inspiration lasercut Mother's Day bouquet

Preparation

Required material

1 sheet solid wood walnut
1 sheet wood veneer maple
1/4 sheet TroGlass Color Gloss green transparent
1/4 sheet TroGlass clear

optional:

hot air gun
bench vice
work gloves

Machine used

Speedy 400 flexx, 100 watts
2" lens or 2.5" lens for TroGlass Clear 10mm
vacuum table with honeycomb cutting table resp. acrylic grid

For this sample you can use any laser machine from the Speedy laser engraver series.

Tip

You can use leftover material for the "blossoms."

flowerbouquet-mothersday.zip

ZIP

Download now

ZIP

Download now

Step by step

Step 1

Step 1: Import design

Make your own design or import our template. Adapt it to your requirements. Send the job for laser cuttting the base plate to the laser using the driver settings below.

Print settings:

Process mode	Resolution	Cut line
Cut Job	1000 dpi	none

Halftone	Others
Color	Optimized geometries, inner geometries first

Step 2

Step 2: Cutting base plate

Put the TroGlass Clear on the acrylic cutting grid of your Trotec laser and insert the 2.5" lens. Then cut the base using the following settings. The parameters can differ depending on the laser machine used and laser power available.

Laser Parameters Cutting

Color	Process	Power (%)	Speed (%)	ppi/Hz
red	Cut CO2	95	0.2	20000

Passes	Air Assist	Z-Offset	Advanced
1	on	-3 mm	-

Info:

We used the standard parameters TroGlass Clear (speed optimized) from JobControl^® .

Step 3

Step 3: Design "grass"

Send the design for the grass to the laser using the settings below.

Print settings:

Process mode	Resolution	Cut line
Standard	500 dpi	none

Halftone	Others
Color	Optimized geometries

Step 4

Step 4: Laser process "grass"

Put the dark green transparent TroGlass onto the acrylic cutting grid of your Trotec laser. Use the 2" lens for this and all following tasks for this application. Engrave and cut the design with the following parameters. The parameters can differ depending on the laser machine used and laser power available.

Laser parameters

Process	Color	Process	Power (%)	Speed (%)
Engraving	black	Engrave CO₂	14	20
Cutting	red	Cut CO₂	100	1

ppi/Hz	Passes	Air Assist	Z-Offset	Advanced
500	1	on	0mm	High Quality
1000	1	on	-	-

Tip:

Start the engraving process from the bottom so that the dust cannot settle on the engraved area.

Step 5

Step 5: Design "Stem"

The next step is to send the design of the solid wood stem to the laser using the driver settings below.

Print settings:

Process mode	Resolution	Cut line
Cut Job	1000 dpi	none

Halftone	Others
-	Optimized geometries

Step 6

Step 6: Laser process "Stem"

Change the acrylic cutting grid against the honeycomb cutting table and position the walnut sheet. Cover the rest of the engraving area to maximize vacuum. Cut the material using the parameters below:

Laser Paramters Cutting

Color	Process	Power (%)	Speed (%)	ppi/Hz
red	Cut CO2	100	1	1000

Passes	Air Assist	Z-Offset	Advanced
1	on	-	-

Tip:

By covering the engraving area, you produce a vacuum which is essential for a clean and consistent cut.

Step 7

Step 7: Design "Blossoms"

Finally, send the design of the abstract blossoms to your laser.

Print settings:

Process mode	Resolution	Cut line
Cut Job	1000 dpi	none

Halftone	Others
-	Optimized Geometries, Inner Geometries first

Step 8

Step 8: Laser process "Blossoms"

Put the maple veneer sheet into the laser, and carefully cover the rest of the engraving table. Then cut the blossoms using the following parameters:

Laser Parameters Cutting

Color	Process	Power (%)	Speed (%)	ppi/Hz
red	Cut CO₂	100	1.2	1000

Passes	Air Assist	Z-Offset	Advanced
1	on	-	-

Tip:

If you cut the entire sheet, focus on the middle of the material to compensate for any differences in thickness.

Step 9

Step 9: Assembly

Put the stem into the base and decorate it with the blossoms. You can combine large and small blossoms. Finally, position the grass into the base, and this inventive Mother's Day bouquet is ready.

Handicraft tip:

Twisted blades of grass are an additional eye catcher. To make these, position the "blades of grass" into a bench vice or another heat-resistant holder. Take a hot air gun and carefully heat the filigree grass. Then deform and twist the hot acrylic. Don't forget to wear gloves! Hold the acrylic in place until it is cooled down. With a little practice, you can get impressive objects.

Preparation

You Will Need

1x sheet - solid wood walnut
1x sheet - wood veneer maple
1/4x sheet - TroGlass Colour Gloss green transparent
1/4x sheet - TroGlass clear
Additional:
Hot Air Gun
Bench Vice
Work Gloves

Machine Used

Speedy 400 flexx, 100 watts
2" lens / 2.5" lens for TroGlass Clear 10mm
Vacuum table with honeycomb cutting table resp. acrylic grid

You can use any machine from the Trotec Speedy series to create this sample.

Tip

Try using the leftover material to create some beautiful 'blossoms'. It's a really good way of making the most out of your material and creating an eye-catching sculpture!

flowerbouquet-mothersday.zip

ZIP

Download now

ZIP

Download now

Step by step

Step 1

Step 1: Import Design

Have a go at creating your own design if you'd like! Or, feel free to import the template that we have provided – just remember to adapt it to your requirements. For our sample, we engraved a recess out of the blue base plate to hold the TroGlass Metallic Ring in place. Then, send the job to your laser machine using these following driver settings:

Print Settings:

Process Mode	Resolution	Cut Line
Standard	500dpi	None

Halftone	Others
Colour	Optimised geometries, inner geometries first

Step 2

Step 2: Cutting the Base Plate

Place the TroGlass Clear onto the acrylic cutting grid and insert the 2.5" lens. Then, cut the base using the following settings. Remember, the parameters may differ depending on what laser machine you are using and its available laser power.

Laser Parameters: Cutting

Colour	Process	Power (%)	Speed (%)	ppi/Hz
Red	Cut CO2	95	0.2	20000

Passes	Air Assist	Z-Offset	Advanced
1	ON	-3mm	-

Info:

We decided to use the standard parameters TroGlass Clear (speed optimised) from JobControl^®. We found that we had the best results this way.

Step 3

Step 3: Design - 'Grass'

Send the 'grass' design to the laser machine using the following settings.

Print Settings:

Process Mode	Resolution	Cut Line
Standard	500dpi	None

Halftone	Others
Colour	Optimised Geometries

Step 4

Step 4: Laser Process - 'Grass'

Begin using the 2" lens now. Place the dark green TroGlass onto the acrylic cutting grid. Engrave and cut out the design using the following parameters. Remember, the parameters may differ depending on what laser machine you are using and its available laser power.

Laser Parameters

Process	Colour	Process	Power (%)	Speed (%)
Engraving	Black	Engrave CO₂	14	20
Cutting	Red	Cut CO₂	100	1

ppi/Hz	Passes	Air Assist	Z-Offset	Advanced
500	1	ON	0mm	High Quality
1000	1	ON	-	-

Tip:

When engraving, start at the bottom and work your way up. This will help stop the dust from settling on the engraved area and creating smudges and scratches.

Step 5

Step 5: Design - 'Stem'

Now, you need to send the solid wood 'stem' design to the laser machine using these following settings:

Print Settings:

Process Mode	Resolution	Cut Line
Cut Job	1000dpi	None

Halftone	Others
-	Optimised Geometries

Step 6

Step 6: Laser Process - 'Stem'

Change over the acrylic cutting grid and swap it for the honeycomb cutting table. Then, position the walnut sheet on top of it. Now, cover the rest of the engraving area so that the vacuum is maximised. Cut the material using these parameters:

Laser Paramters: Cutting

Colour	Process	Power (%)	Speed (%)	ppi/Hz
Red	Cut CO2	100	1	1000

Passes	Air Assist	Z-Offset	Advanced
1	ON	-	-

Tip:

By covering the entire engraving area, you will produce a vacuum. This is essential for a clean, consistent cut.

Step 7

Step 7: Design - 'Blossoms'

Finally, send the abstract bloosom design to your laser machine.

Print Settings:

Process Mode	Resolution	Cut Line
Cut Job	1000dpi	None

Halftone	Others
-	Optimised Geometries, Inner Geometries first

Step 8

Step 8: Laser Process - 'Blossoms'

Place the maple veneer sheet into the laser machine and carefully cover up the rest of the engraving table. Then, cut the blossoms out using the following laser parameters:

Laser Parameters: Cutting

Colour	Process	Power (%)	Speed (%)	ppi/Hz
Red	Cut CO₂	100	1.2	1000

Passes	Air Assist	Z-Offset	Advanced
1	ON	-	-

Tip:

If you decide to cut the entire sheet for this part, focus on the very middle of the material. This will compensate for any tiny inconsistencies in thickness.

Step 9

Step 9: Assembly

Stick the stem into the base and decorate it with all your lovely little blossoms. You can combine large and small blossoms to give the piece a random, natural effect. Finally, position the grass into the base plate as well. Your beautiful Mother's Day bouquet is now ready to give to your mum!

Additional Bonus Step:

Twisted blades of grass can be an additional eye-catcher. If you want to make these, you just need to position the 'blades of grass' into a bench vice / heat resistant holder. Then, take a hot air gun and carefully heat the shards of grass. Once they are malleable, deform and twist the hot acrylic. It is very important that you wear gloves if you decide to complete this little bonus step. Hold the acrylic in place until it has cooled down and hardened again. It requires patience, but this can really lift your projects to new heights!

Inspiration

Try using different colours and shades of acrylic! Try some TroGlass Satins or maybe even some TroGlass Frosted. With a little extra creativity, you can even try turning this 'flower bouquet' into an abstract piece of laser art. The sky is your only limit with laser technology!

Speedy series
The ideal laser engraver and cutter for personalisation.

Discover laser engravers and cutters

Questions about applications or settings?
We're happy to advise you from A for Air assist to Z for z-offset.

Request more
information now.

All laser machines

All laser machines

All applications & industries

All materials

Required material

Machine used

Tip

flowerbouquet-mothersday.zip

Step 1: Import design

Print settings:

Step 2: Cutting base plate

Laser Parameters Cutting

Info:

Step 3: Design "grass"

Print settings:

Step 4: Laser process "grass"

Laser parameters

Tip:

Step 5: Design "Stem"

Print settings:

Step 6: Laser process "Stem"

Laser Paramters Cutting

Tip:

Step 7: Design "Blossoms"

Print settings:

Step 8: Laser process "Blossoms"

Laser Parameters Cutting

Tip:

Step 9: Assembly

Handicraft tip:

You Will Need

Additional:

Machine Used

Tip

flowerbouquet-mothersday.zip

Step 1: Import Design

Print Settings:

Step 2: Cutting the Base Plate

Laser Parameters: Cutting

Info:

Step 3: Design - 'Grass'

Print Settings:

Step 4: Laser Process - 'Grass'

Laser Parameters

Tip:

Step 5: Design - 'Stem'

Print Settings:

Step 6: Laser Process - 'Stem'

Laser Paramters: Cutting

Tip:

Step 7: Design - 'Blossoms'

Print Settings:

Step 8: Laser Process - 'Blossoms'

Laser Parameters: Cutting

Tip:

Step 9: Assembly

Additional Bonus Step: