선택 방법
용도에 맞는 렌즈

올바른 렌즈를 선택하는 것이 레이저 결과를 완성하는 열쇠가 될 수 있습니다. 다음 가이드를 사용하여 응용 프로그램에 사용해야하는 렌즈를 결정하십시오.

적합한 렌즈를 선택하는 것은 까다로울 수 있습니다.

매개 변수가 잘되고 포커스가 올바르게 설정되었지만 어떻게 든 조각이 올바르지 않습니다. 이런 일이 당신에게 일어 났습니까? 이것은 렌즈 문제 일 가능성이 큽니다. 올바른 렌즈는 올바른 매개 변수와 최적의 초점 조정만큼 중요합니다.

올바른 렌즈를 선택하려면 다음을 고려해야합니다.:

  • 레이저 장치의 출력
  • 재료
  • 그래픽의 상세 수준
  • 해상도 (dpi)
  • 재료의 두께

The rule of thumb:

그래픽이 섬세하고 세밀할수록 렌즈를 더 작게 선택해야합니다. 두꺼운 소재를 자르기 위해 최대 크기의 렌즈를 사용하는 것이 좋습니다. 자세한 내용은 아래 표를 참조하십시오.

Speedy 및 SP 렌즈 포트폴리오

다음 표는 Speedy 레이저 장치 및 해당 응용 프로그램에서 사용할 수있는 모든 렌즈를 보여줍니다.

1.5 inch CO2 세부 묘사가 잘된 그래픽, (해상도 > 500 dpi), 얇은 글씨로 고무 도장
 
낮은 레이저 출력, 얇은 재료 (예 : 종이), 아크릴 < 6 mm, 중간강도 목재 < 8 mm.
2.0 inch CO2 중간 정도의 세부 묘사 및 해상도 (500 dpi 해상도, 100 dpi 해상도까지 축소 된 그래픽), 표준 조각
 
Medium laser power, 아크릴 < 8 mm, 목재 of medium hardness < 12 mm.
2.0 inch CO2 clearance 렌즈 Mainly used for cutting See 2.0 inch 렌즈.
Increases the distance between laser head and material. Is especially useful if the increased distance is required due to the material and the 그래픽 파일
2.5 inch CO2 Graphics with low detail, low resolution (< 500 dpi). 조각 on heat-sensitive materials (e. g. laminate) if large areas have to be removed completely High laser power, 아크릴 <12 mm, 목재 of medium hardness <15 mm
Better quality of edges during 레이저 컷팅 than for lower focal distances
2.5 inch CO2 clearance 렌즈 Used mainly for cutting See 2.5 inch 렌즈.
Increases the distance between laser head and material. Is especially useful if the increased distance is required due to the material and the 그래픽 파일.
2.85 inch flexx

Standard 렌즈 for Speedy flexx 시리즈. Is transmissive for both CO₂ lasers and fiber lasers. Both laser sources can be used without changing the 렌즈.

Other characteristics as 2.5 inch CO2 렌즈 or 3.2 inch fiber 렌즈

Characteristics as 2.5 inch CO2 렌즈 or 3.2 inch 파이버 렌즈
3.2 inch fiber Standard 렌즈 for fiber lasers with extremely small focal diameter. Graphics with fine detail, ( > 500 dpi resolution)
 
 
3.75 inch CO2 렌즈 for SP500 로타리 조각 unit. Permits 조각 of round objects with diameters of less than 50 mm
 
 
4.0 inch CO2 조각 by burning of 목재, laser 조각 of graphics with low detail with high laser powers
 
foam 고무
5.0 inch CO2 Is not used for laser 조각 High laser power, 아크릴 < 25 mm, 목재 of medium hardness < 20 mm
Better quality of edges during 레이저 컷팅 than for smaller focal distances
5.0 inch fiber 렌즈 for fiber lasers if materials that are not absolutely plane are to be labeled. The greater focal distance results in a greater tolerance during focusing.  
7.5 inch CO2 (for SP1500) Is not used for laser 조각
 
High laser power, 아크릴 < 40 mm,
Better quality of edges during 레이저 컷팅 than for smaller focal distances
렌즈 When to use for 조각/marking When to use for cutting

각 장치마다 모든 렌즈를 사용할 수있는 것은 아닙니다. 이상적인 렌즈 선택에 도움을 드리겠습니다.

우리는 당신에게 조언 할 것을 기뻐할 것입니다.


일반 용어로 기술 기능

다음은 렌즈에 대해 논의 할 때 사용되는 용어집입니다.

Focal length
렌즈와 가장 작은 빔 지름 (= 초점) 사이의 거리.

Focus
레이저 빔이 최적으로 집속되고 가능한 가장 작은 빔 직경으로 수렴하는 영역입니다.

Beam diameter
초점 전후에 점점 커지는 레이저 빔의 직경.

렌즈의 초점 거리가 길수록 빔 직경이 커집니다. 레이저의 에너지는 렌즈에 의해 정의 된 초점에 초점을 맞 춥니 다. 렌즈의 초점 거리가 클수록 레이저 에너지가 적용되는 표면 또한 커집니다. 큰 렌즈를 사용하면 재료가 절단되는 것이 아니라 가열되는 경우가 있습니다.

Focus tolerance (depth of focus)
보가 가장 작은 직경을 갖는 영역.

렌즈가 클수록 (= 렌즈의 초점 거리가 길어질수록) 초점 허용 오차가 더 길어집니다. 즉, 5 인치 렌즈의 초점 공차는 2.5 인치 렌즈의 두 배가됩니다. 두꺼운 재료를 자르려는 경우 특히 중요합니다.


당사의 레이저 전문가로부터 개별 지원을 받으십시오.

기술 지원
내부고발자 시스템의 troGROUP Logo