Seri Speedy: Mesin pemotong dan laser CO2 pengukir untuk format hingga 1016 x 610 mm
⚫ Pengukiran | ⚫ Pemotongan | ⚫ Penandaan |
Jenis Laser: | Laser CO₂, Flexx, atau Fiber |
---|---|
Bidang kerja: | 610 x 305 hingga 1016 x 610 mm |
Tinggi bidang kerja maks.: | 125 - 305 mm |
Daya Laser: | 20 - 120 watt |
Seri SP: Laser CO2 pemotong untuk bahan dengan format besar.
⚫ Pengukiran | ⚫ Pemotongan | ⎯ Penandaan |
Jenis Laser: | Laser CO₂ |
---|---|
Bidang kerja: | 1245 x 710 hingga 3250 x 3210 mm |
Tinggi bidang kerja maks.: | 50 - 112 mm |
Daya Laser: | 40 - 400 watt |
Stasiun laser penanda dengan kepala penanda galvo. Bidang penanda hingga 44,1 x 25,0 inci.
⚫ Pengukiran | ⎯ Pemotongan | ⚫ Penandaan |
Jenis Laser: | Laser CO₂ atau Fiber |
---|---|
Max. work area: | 190 x 190 hingga 1300 x 450 mm |
Tinggi bidang kerja maks.: | 250 - 764 mm |
Daya Laser: | 20 - 100 watt / 20 watt MOPA |
Step by step instructions
In this tutorial we will show you how to create original voucher packaging with Trotec LaserPaper Color.
For this sample you can use any laser machine from the Speedy laser engraver series.
We used the 2" lens because it produces a more uniform result on large-area engravings.
Make your own design and adjust according to your preferences. We engraved the camouflage design with its three different grayscales in one engraving process. How this exactly works is described here. Send the graphic for the outer shell to the laser using the settings below:
Process mode | Resolution | Cut line |
---|---|---|
Relief | 500 dpi | none |
Halftone | Others |
---|---|
Color | enhanced geometries, inner geometries first |
Put the dark blue LaserPaper Color into your Trotec laser and focus exactly on the surface. Make the parameter settings. The parameters can differ depending on the laser machine used and laser power available.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
black | Engraving CO2 | 40 | 20 | 500 |
red | Engraving CO2 | 9 | 2 | 1000 |
blue | Cutting CO2 | 18 | 2 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 0 | High Quality |
1 | on | 0 | - |
1 | on | 0 | - |
Cover the remaining working area with standard paper to achieve full vacuum.
Send every single graphic for frame and strip curtain to the laser using the following parameters:
Process mode | Resolution | Cut line |
---|---|---|
Vector job | 1000 dpi | none |
Halftone | Others |
---|---|
Color | Inner geometries first |
Put the slate gray LaserPaper Color into your Trotec laser and cut the frame. Then cut the strip curtain out of the golden LaserPaper. You can use the same parameters for both designs.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
blue | Cut CO2 | 18 | 2 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 0 | - |
Take the frame and secure it on the inner part of the cover (where the grip hole is) using liquid glue or double-sided adhesive disks. Now take the strip curtain and apply double-sided adhesive tape on the bottom of the far left stripe, and on top of the far right paper strip. Insert the strip curtain into the cover and secure it. If you open the card, the stripes move like a curtain and are a great eye catcher.