Seri Speedy: Mesin pemotong dan laser CO2 pengukir untuk format hingga 1016 x 610 mm
⚫ Pengukiran | ⚫ Pemotongan | ⚫ Penandaan |
Jenis Laser: | Laser CO₂, Flexx, atau Fiber |
---|---|
Bidang kerja: | 610 x 305 hingga 1016 x 610 mm |
Tinggi bidang kerja maks.: | 125 - 305 mm |
Daya Laser: | 20 - 120 watt |
Seri SP: Laser CO2 pemotong untuk bahan dengan format besar.
⚫ Pengukiran | ⚫ Pemotongan | ⎯ Penandaan |
Jenis Laser: | Laser CO₂ |
---|---|
Bidang kerja: | 1245 x 710 hingga 3250 x 3210 mm |
Tinggi bidang kerja maks.: | 50 - 112 mm |
Daya Laser: | 40 - 400 watt |
Stasiun laser penanda dengan kepala penanda galvo. Bidang penanda hingga 44,1 x 25,0 inci.
⚫ Pengukiran | ⎯ Pemotongan | ⚫ Penandaan |
Jenis Laser: | Laser CO₂ atau Fiber |
---|---|
Max. work area: | 190 x 190 hingga 1300 x 450 mm |
Tinggi bidang kerja maks.: | 250 - 764 mm |
Daya Laser: | 20 - 100 watt / 20 watt MOPA |
Make a three-dimensional winners' trophy using Trotec materials and 3D relief laser engraving
You can use any other machine of the Speedy Flexx laser engraver series.
TroGlass Satins and TroGlass Metallic have a very high-end finish
You can make your own design or import our template and then adapt it to your requirements. We have engraved a recess out of the base plate to hold the TroGlass Metallic ring.
Process mode | Resolution | Cut line |
---|---|---|
Standard | 500dpi | none |
Halftone | Other |
---|---|
colour | Optimized geometries |
Put TroGlass Satin Black on the acrylic grid of your Trotec laser. Engrave and cut the base plate using the parameters below. The parameters can differ depending on the laser machine used and laser power available.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
black | Engrave CO2 | 40 | 10 | 500 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 2mm | - |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 8 | 0.8 | 5000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 1 mm | - |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
blue | Cut CO2 | 95 | 0.8 | 5000 |
Passes | Air Assist | Z-offset | Advanced |
---|---|---|---|
1 | on | - | - |
Send the job for the TroGlass Metallic ring to the laser using the driver settings below.
Process mode | Resolution | Cut line | Halftone | Others |
---|---|---|---|---|
Standard | 600dpi | none | - | - |
Put the TroGlass Metallic sheet on the acrylic cutting table and engrave the job using the parameters below:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
black | Engrave CO2 | 16 | 20 | 600 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 1 mm | - |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut Co2 | 50 | 0.2 | 5000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | - | - |
Tip: We used the JobControl® parameters for TroGlass optimized for quality.
Finally, send the files for 3-dimensional wood engravings and the other wooden parts to the laser:
Process mode | Resolution | Cut line | Halftone | Others |
---|---|---|---|---|
Standard | 500dpi | None | - | - |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Black | Engrave CO2 | 100 | 30 | 500 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
3 (!!) | On | - | - |
Color | Process | Power (%) | Speed (%) | ppi / Hz |
---|---|---|---|---|
Red | Cut CO2 | 100 | 1 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | On | - | - |
Tip:
When engraving deeply into wood, it can be helpful to cut the job first and engrave the job afterwards.
Clean the two acrylic pieces with a damp cloth. The wood relief engraving can be cleaned best with some water and a tooth brush. Here you can find tips for correct cleaning.
Put the acrylic glue on the engraved ring of the base plate and position the TroGlass Metallic ring on it. Press down firmly and allow the glue to cure.
Put double-sided adhesive tape or dots where the wooden relief shall be positioned and fix it.
Take the wooden spacer and apply double-sided adhesive tape on both sides. Position it on the left and the right of the black base plate. Make sure to have a rectangular contact surface so that the trophy stands upright.
Finally, fix the lettering "winner" and the corresponding back on the spacers to complete this elegant trophy.
Combine other types of solid wood and TroGlass materials to adapt the trophy to your customers' requirements.