Seri Speedy: Mesin pemotong dan laser CO2 pengukir untuk format hingga 1016 x 610 mm
⚫ Pengukiran | ⚫ Pemotongan | ⚫ Penandaan |
Jenis Laser: | Laser CO₂, Flexx, atau Fiber |
---|---|
Bidang kerja: | 610 x 305 hingga 1016 x 610 mm |
Tinggi bidang kerja maks.: | 125 - 305 mm |
Daya Laser: | 20 - 120 watt |
Seri SP: Laser CO2 pemotong untuk bahan dengan format besar.
⚫ Pengukiran | ⚫ Pemotongan | ⎯ Penandaan |
Jenis Laser: | Laser CO₂ |
---|---|
Bidang kerja: | 1245 x 710 hingga 3250 x 3210 mm |
Tinggi bidang kerja maks.: | 50 - 112 mm |
Daya Laser: | 40 - 400 watt |
Stasiun laser penanda dengan kepala penanda galvo. Bidang penanda hingga 44,1 x 25,0 inci.
⚫ Pengukiran | ⎯ Pemotongan | ⚫ Penandaan |
Jenis Laser: | Laser CO₂ atau Fiber |
---|---|
Max. work area: | 190 x 190 hingga 1300 x 450 mm |
Tinggi bidang kerja maks.: | 250 - 764 mm |
Daya Laser: | 20 - 100 watt / 20 watt MOPA |
Step by step instruction for your Trotec laser
In this tutorial we will show you how to use the "Kerf Cut" process to make a napkin ring out of wood.
You can produce this design using any laser machine from the Trotec Laser Speedy series.
We used a 1.5" lens due to the detailed cuts of the design.
Import our graphic and adapt it to your requrements. We have already tested cutting techniques for bending applications for you. In our Tips & Tricks "Kerf Cut" you'll find further examples of how you can use this application.
Process mode | Resolution | Cut line |
---|---|---|
Vector Job | 1000dpi | No |
Halftone | Others |
---|---|
Color | Optimized Geometries, Inner Geometries first |
Place the honeycomb cutting table in your Trotec laser and attach the small nozzle to the laser head. Place the walnut plate in your laser and cover the remaining working surface. The parameters may vary depending on the laser machine used and available laser power.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut CO2 | 100 | 1.2 | 1,000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | On | 0mm | - |
We explain in our Tips & Tricks why you should choose the right nozzle for this application. How to choose the right nozzle.
Send the graphic for the TroLase Foil decoration to your Trotec Laser machine using the following print settings:
Process mode | Resolution | Cut line |
---|---|---|
Vector Job | 1000dpi | No |
Halftone | Others |
---|---|
- | Optimized Geormetries, Inner Geometries First |
Remove the honeycomb cutting table and install the acrylic grid cutting table and the large nozzle. Insert the TroLase Foil into the laser and cover the rest of the working area.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut CO2 | 20 | 1.0 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | On | 0mm | - |
It is especially important to closely monitor the vacuum with the thin TroLase Foil to make sure a flat surface is maintained throughout the laser process.
Clean the two separate parts with a damp cloth. It is also a good idea to clean the back of the wooding ring so that the napkin does not get dirty later.
Keep the wooden napkin ring flat and glue the TroLase Foil about half off.
To make sure that the overhanging half does not stick to the napkin, we scored and removed half of the adhesive foil on the back with a craft knife. To finish, form a ring around a cloth napkin and secure it with the circular connector.
Use other types of veneered wood or TroLase Foil colors to match the look of the rest of the table top.
Design a whole wedding table top using your Trotec laser and Trotec materials. Inspirations can be found in our DIYs.