Seri Speedy: Mesin pemotong dan laser CO2 pengukir untuk format hingga 1016 x 610 mm
⚫ Pengukiran | ⚫ Pemotongan | ⚫ Penandaan |
Jenis Laser: | Laser CO₂, Flexx, atau Fiber |
---|---|
Bidang kerja: | 610 x 305 hingga 1016 x 610 mm |
Tinggi bidang kerja maks.: | 125 - 305 mm |
Daya Laser: | 20 - 120 watt |
Seri SP: Laser CO2 pemotong untuk bahan dengan format besar.
⚫ Pengukiran | ⚫ Pemotongan | ⎯ Penandaan |
Jenis Laser: | Laser CO₂ |
---|---|
Bidang kerja: | 1245 x 710 hingga 3250 x 3210 mm |
Tinggi bidang kerja maks.: | 50 - 112 mm |
Daya Laser: | 40 - 400 watt |
Stasiun laser penanda dengan kepala penanda galvo. Bidang penanda hingga 44,1 x 25,0 inci.
⚫ Pengukiran | ⎯ Pemotongan | ⚫ Penandaan |
Jenis Laser: | Laser CO₂ atau Fiber |
---|---|
Max. work area: | 190 x 190 hingga 1300 x 450 mm |
Tinggi bidang kerja maks.: | 250 - 764 mm |
Daya Laser: | 20 - 100 watt / 20 watt MOPA |
Learn how you can produce a decorative and extraordinary Mother's Day gift.
optional:
For this sample you can use any laser machine from the Speedy laser engraver series.
You can use leftover material for the "blossoms."
Make your own design or import our template. Adapt it to your requirements. Send the job for laser cuttting the base plate to the laser using the driver settings below.
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
Color | Optimized geometries, inner geometries first |
Put the TroGlass Clear on the acrylic cutting grid of your Trotec laser and insert the 2.5" lens. Then cut the base using the following settings. The parameters can differ depending on the laser machine used and laser power available.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 95 | 0.2 | 20000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | -3 mm | - |
We used the standard parameters TroGlass Clear (speed optimized) from JobControl® .
Send the design for the grass to the laser using the settings below.
Process mode | Resolution | Cut line |
---|---|---|
Standard | 500 dpi | none |
Halftone | Others |
---|---|
Color | Optimized geometries |
Put the dark green transparent TroGlass onto the acrylic cutting grid of your Trotec laser. Use the 2" lens for this and all following tasks for this application. Engrave and cut the design with the following parameters. The parameters can differ depending on the laser machine used and laser power available.
Process | Color | Process | Power (%) | Speed (%) |
---|---|---|---|---|
Engraving | black | Engrave CO2 | 14 | 20 |
Cutting | red | Cut CO2 | 100 | 1 |
ppi/Hz | Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|---|
500 | 1 | on | 0mm | High Quality |
1000 | 1 | on | - | - |
Start the engraving process from the bottom so that the dust cannot settle on the engraved area.
The next step is to send the design of the solid wood stem to the laser using the driver settings below.
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
- | Optimized geometries |
Change the acrylic cutting grid against the honeycomb cutting table and position the walnut sheet. Cover the rest of the engraving area to maximize vacuum. Cut the material using the parameters below:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 100 | 1 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | - | - |
By covering the engraving area, you produce a vacuum which is essential for a clean and consistent cut.
Finally, send the design of the abstract blossoms to your laser.
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
- | Optimized Geometries, Inner Geometries first |
Put the maple veneer sheet into the laser, and carefully cover the rest of the engraving table. Then cut the blossoms using the following parameters:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 100 | 1.2 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | - | - |
If you cut the entire sheet, focus on the middle of the material to compensate for any differences in thickness.
Put the stem into the base and decorate it with the blossoms. You can combine large and small blossoms. Finally, position the grass into the base, and this inventive Mother's Day bouquet is ready.
Twisted blades of grass are an additional eye catcher. To make these, position the "blades of grass" into a bench vice or another heat-resistant holder. Take a hot air gun and carefully heat the filigree grass. Then deform and twist the hot acrylic. Don't forget to wear gloves! Hold the acrylic in place until it is cooled down. With a little practice, you can get impressive objects.
Use other colors of TroGlass, e.g. TroGlass Satins or TroGlass Frosted and transform the "flower bouquet" into an abstract sculpture.