Ramo decorativo del Día de la Madre hecho de TroGlass y chapa de madera
Descubra cómo hacer un regalo decorativo y extraordinario para el Día de la Madre.
Preparación
Required material
- 1 sheet solid wood walnut
- 1 sheet wood veneer maple
- 1/4 sheet TroGlass Color Gloss green transparent
- 1/4 sheet TroGlass clear
optional:
- hot air gun
- bench vice
- work gloves
Machine used
- Speedy 400 flexx, 100 watts
- 2" lens or 2.5" lens for TroGlass Clear 10mm
- vacuum table with honeycomb cutting table resp. acrylic grid
For this sample you can use any laser machine from the Speedy laser engraver series.
Tip
You can use leftover material for the "blossoms."
Paso a paso

Step 1: Import design
Make your own design or import our template. Adapt it to your requirements. Send the job for laser cuttting the base plate to the laser using the driver settings below.
Print settings:
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
Color | Optimized geometries, inner geometries first |

Step 2: Cutting base plate
Put the TroGlass Clear on the acrylic cutting grid of your Trotec laser and insert the 2.5" lens. Then cut the base using the following settings. The parameters can differ depending on the laser machine used and laser power available.
Laser Parameters Cutting
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 95 | 0.2 | 20000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | -3 mm | - |
Info:
We used the standard parameters TroGlass Clear (speed optimized) from JobControl® .

Step 3: Design "grass"
Send the design for the grass to the laser using the settings below.
Print settings:
Process mode | Resolution | Cut line |
---|---|---|
Standard | 500 dpi | none |
Halftone | Others |
---|---|
Color | Optimized geometries |

Step 4: Laser process "grass"
Put the dark green transparent TroGlass onto the acrylic cutting grid of your Trotec laser. Use the 2" lens for this and all following tasks for this application. Engrave and cut the design with the following parameters. The parameters can differ depending on the laser machine used and laser power available.
Laser parameters
Process | Color | Process | Power (%) | Speed (%) |
---|---|---|---|---|
Engraving | black | Engrave CO2 | 14 | 20 |
Cutting | red | Cut CO2 | 100 | 1 |
ppi/Hz | Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|---|
500 | 1 | on | 0mm | High Quality |
1000 | 1 | on | - | - |
Tip:
Start the engraving process from the bottom so that the dust cannot settle on the engraved area.

Step 5: Design "Stem"
The next step is to send the design of the solid wood stem to the laser using the driver settings below.
Print settings:
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
- | Optimized geometries |

Step 6: Laser process "Stem"
Change the acrylic cutting grid against the honeycomb cutting table and position the walnut sheet. Cover the rest of the engraving area to maximize vacuum. Cut the material using the parameters below:
Laser Paramters Cutting
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 100 | 1 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | - | - |
Tip:
By covering the engraving area, you produce a vacuum which is essential for a clean and consistent cut.

Step 7: Design "Blossoms"
Finally, send the design of the abstract blossoms to your laser.
Print settings:
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
- | Optimized Geometries, Inner Geometries first |

Step 8: Laser process "Blossoms"
Put the maple veneer sheet into the laser, and carefully cover the rest of the engraving table. Then cut the blossoms using the following parameters:
Laser Parameters Cutting
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 100 | 1.2 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | - | - |
Tip:
If you cut the entire sheet, focus on the middle of the material to compensate for any differences in thickness.

Step 9: Assembly
Put the stem into the base and decorate it with the blossoms. You can combine large and small blossoms. Finally, position the grass into the base, and this inventive Mother's Day bouquet is ready.
Handicraft tip:
Twisted blades of grass are an additional eye catcher. To make these, position the "blades of grass" into a bench vice or another heat-resistant holder. Take a hot air gun and carefully heat the filigree grass. Then deform and twist the hot acrylic. Don't forget to wear gloves! Hold the acrylic in place until it is cooled down. With a little practice, you can get impressive objects.
Preparación
Material necesario
- 1 plancha de madera maciza de nogal
- 1 plancha de madera laminada de arce
- 1/4 plancha de TroGlass Color Gloss verde/transparente
- 1/4 plancha de TroGlass Clear
-
Opcional:
- Pistola de aire caliente
- Sargento de mesa
- Guantes de trabajo
Máquina usada
- Speedy 400 flexx de 100 vatios
- Lente de 2" o 2.5" para TroGlass Clear 10mm
- Mesa de efecto vacío con mesa de corte en panal de abeja o de corte de acrílico
Para hacer esta muestra puede utilizar cualquier máquina láser de la serie Speedy.
Consejo
Puede usar el material sobrante para hacer las «flores»
Paso a paso

Paso 1: Importar / Crear plantilla
Haga su propio diseño o importe nuestra plantilla y personalicela a su gusto. Envíe el trabajo al láser usando los siguientes ajustes de impresión:
Ajustes de impresión:
Proceso | Resolución | Línea de corte |
---|---|---|
Trabajo de corte | 1000 dpi | No hay |
Medio tono | Otros |
---|---|
Color | Geometrías mejoradas, Geometrías internas primero |

Paso 2: Corte de la placa de base
Coloque la plancha de TroGlass Clear en la mesa de corte de acrílico de su láser y utilice la lente de 2,5 pulgadas. Corte la base usando los siguientes parámetros. Tenga en cuenta que los parámetros recomendados pueden variar dependiendo de la máquina láser utilizada y de la potencia de la misma.
Parámetros láser
Color | Proceso | Potencia (%) | Velocidad (%) | ppi/Hz |
---|---|---|---|---|
Rojo | Corte CO2 | 95 | 0,2 | 20000 |
Pasadas | Aire Asistido | Offset Z | Avanzado |
---|---|---|---|
1 | Encendido | -3 mm | - |
Consejo:
Utilice los parámetros estándar para TroGlass Clear de JobControl® optimizados para velocidad.

Paso 3: Diseño "hierba"
Envíe el diseño para la hierba al láser usando los siguientes ajustes de impresión:
Ajustes de impresión:
Proceso | Resolución | Línea de corte |
---|---|---|
Estándar | 500 dpi | ninguno |
Medio tono | Otros |
---|---|
Color | Geometrías mejoradas |

Paso 4: Procesamiento láser
Coloque la plancha de TroGlass transparente verde oscuro en la mesa de corte de acrílico de su láser y utilice la lente de 2 pulgadas. Grabe y corte el diseño con los siguientes parámetros. Tenga en cuenta que los parámetros recomendados pueden variar dependiendo de la máquina láser utilizada y de la potencia de la misma.
Parámetros láser
Proceso | Color | Proceso | Potencia (%) | Velocidad (%) |
---|---|---|---|---|
Grabado | Negro | Grabado CO2 | 14 | 20 |
Corte | Rojo | Corte CO2 | 100 | 1 |
ppi/Hz | Pasadas | Aire Asistido | Offset Z | Avanzado |
---|---|---|---|---|
500 | 1 | Encendido | 0mm | Alta Calidad |
1000 | 1 | Encendido | - | - |
Consejo:
Realice el grabado de abajo hacia arriba para reducir los residuos que se depositan en el material.

Paso 5: Diseño "tallo"
Envíe el diseño del tallo de madera al láser usando los siguientes ajustes de impresión:
Ajustes de impresión:
Proceso | Resolución | Línea de corte |
---|---|---|
Trabajo de corte | 1000 dpi | No hay |
Medio tono | Otros |
---|---|
- | geometrías mejoradas |

Paso 6: Procesamiento láser
Cambie la mesa de corte de acrílico por la mesa de corte en panal de abeja y coloque la plancha de madera nogal. Cubra el resto del área de trabajo para aumentar el efecto vacío. Corte el material usando los siguientes parámetros:
Parámetros láser para corte
Color | Proceso | Potencia (%) | Velocidad (%) | ppi/Hz |
---|---|---|---|---|
Rojo | Corte CO2 | 100 | 1 | 1000 |
Pasadas | Aire Asistido | Offset Z | Avanzado |
---|---|---|---|
1 | Encendido | - | - |
Consejo:
Cubra el área de trabajo restante para producir un mayor efecto de vacío y conseguir un corte limpio y de calidad.

Paso 7: Diseño de "flores"
Por último, envíe el diseño de las flores al láser.
Ajustes de impresión:
Proceso | Resolución | Línea de corte |
---|---|---|
Trabajo de corte | 1000 dpi | No hay |
Medio tono | Otros |
---|---|
- | Geometrías mejoradas, Geometrías internas primero |

Paso 8: Procesamiento láser
Coloque la plancha de madera arce en el láser y cubra el resto del área de trabajo. Corte las flores usando los siguientes parámetros:
Parámetros láser
Color | Proceso | Potencia (%) | Velocidad (%) | ppi/Hz |
---|---|---|---|---|
Rojo | Corte CO2 | 100 | 1,2 | 1000 |
Pasadas | Aire Asistido | Offset Z | Avanzado |
---|---|---|---|
1 | Encendido | - | - |
Consejo:
En caso de utilizar toda la plancha de madera, recomendamos enfocar en la mitad del material para compensar posibles diferencias de grosor.

Paso 9: Montaje
Coloque el tallo en la base y decórelo con las flores, para conseguir un efecto más llamativo puede combinar flores grandes y pequeñas. Finalmente, coloque la hierba en la base y este original ramo del Día de la Madre estará listo.
Consejo:
Las hojas de hierba ligeramente dobladas dan un valor añadido a la pieza. Para hacerlo, coloque las "hojas de hierba" en un sargento de mesa u otro soporte resistente al calor. Con la ayuda de una pistola de aire caliente podrá dar forma al acrílico. Mantenga el acrílico en su lugar hasta que se enfríe. ¡No olvide usar guantes!
Un poco de inspiración
Use otros materiales de la gama TroGlass, p. ej. TroGlass Satins o TroGlass Frosted y transforme el "ramo de flores" en una escultura abstracta.