Carteles de Covid-19
Aquí podrá encontrar plantillas para crear rápidamente carteles de Covid-19 de TroLase, TroLase Foil y TroGlass.
Preparación
Required material
Sign "Wash your hands" Variant 1
- 1/4 sheet TroLase black/yellow 1.6 mm L704-206
- 1/4 sheet TroLase blue/white 1.6 mm L512-206 with double-sided adhesive foil on the back
Required material
Sign "Wash your hands" Variant 2
- 1/4 sheet TroGlass reverse glossy/white
- 1/4 sheet TroLase blue/white 1.6 mm with double-sided adhesive foil on the back
- Acrylic paint in black
Required material
Sticker "Keep distance"
- 1/4 sheet TroLase Foil red/white 0.2 mm
Machine used:
- Speedy 300
- 80 watts
- 1.5" lens
- Aluminum cutting grid table or honeycomb cutting tabletop
This sample can be produced with any other machine of the Speedy laser engravers.
Tip:
When working with TroLase or TroLase Foil, the following applies: If you use the entire work surface, use a vacuum table or an adhesive mat so that the material lies flat over the entire surface. Otherwise, cover the work surface with paper to create an optimal vacuum.
Paso a paso

Step 1: Import/Create Print & Laser Template
Create your own design or use our template. Now send the job to the laser with the settings below.
Important: If you use TroGlass Reverse, the file must be mirrored.
Print settings
Process mode | Resolution | Cut line |
---|---|---|
standard | 500dpi | none |
Halftone | Other |
---|---|
- | Optimized geometries, inner geometries first |

Step 2: Laser process
Now make the parameter settings. Our suggested parameters may vary depending on the laser machine used and the available laser power.
Remove the protective foil from the TroLase Foil or TroLase surface and then place the material in your laser. If you use TroGlass Reverse it is recommended to remove the foil after the laser process.
Laser Parameters:
Material | Color | Process | Power (%) | Speed (%) | ppi/Hz | Passes | Air Assist | Z-Offset | Direction | Advanced |
---|---|---|---|---|---|---|---|---|---|---|
TroLase Foil | black | Engrave CO2 | 55 | 80 | 500 | 1 | off | 1.5 | bottom to top | - |
red | Cut CO2 | 40 | 1 | 2000 | 1 | on | 0 | - | - | |
TroLase | black | Engrave CO2 | 65 | 80 | 600 | 1 | off | 1.5 | bottom to top | - |
red | Cut CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - | |
TroGlass Reverse | black | Engrave CO2 | 18 | 20 | 500 | 1 | on | 0 | bottom to top | - |
red | Cut CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - |

Step 3: Assembly
To attach the parts to each other, first remove the protective film on the back of the blue TroLase shield. Now stick the TroLase label onto the yellow TroLase or the white TroGlass Reverse label according to the markings.
The signs are now ready for use!
You can of course produce these signs in all possible colour and material combinations.
Preparación
Material necesario
Cartel "Lávate las manos" Opción 1
- 1/4 de plancha TroLase negro/amarillo 1.6 mm L704-206
- 1/4 de plancha TroLase azul/blanco de 1,6 mm L512-206 con adhesivo doble cara en la parte posterior
Material necesario:
Cartel "Lávate las manos" opción 2
- 1/4 de plancha TroGlass Reverse brillante/blanco
- 1/4 de plancha TroLase azul/blanco de 1,6 mm con adhesivo de doble cara en la parte posterior
- Pintura acrílica en negro
Material necesario
Adhesivo "Mantén la distancia"
- 1/4 de plancha TroLase Foil rojo/blanco 0,2 mm
Máquina recomendada:
- Speedy 300
- 80 vatios
- Lente 1.5 pulgadas
- Mesa de rejilla de aluminio o soporte de corte de panal
Este patrón puede ser producido con cualquier máquina de la serie Speedy.
Tip:
Cuando se trabaja con TroLase o TroLase Foil se aplica lo siguiente: Si se utiliza toda la superficie de trabajo, se debe utilizar una mesa de vacío o una alfombra adhesiva para que el material quede plano en toda la superficie. De lo contrario, cubra la superficie de trabajo con papel para crear un vacío óptimo.
Paso a paso

Paso 1: Importar/Crear plantilla de impresión y láser
Crea tu propio diseño o usa nuestra plantilla.Ahora envía el trabajo al láser con los siguientes ajustes.
Importante: Si usas TroGlass Reverse, el archivo debe ser grabado en modo espejo.
Ajustes de impresión
Tipo de proceso | Resolución | Línea de corte |
---|---|---|
estándar | 500dpi | ninguna |
Medio tono | Otros |
---|---|
- | Geometrías optimizadas, geometrías interiores primero |

Paso 2: Proceso láser
Ahora haga los ajustes de los parámetros. Nuestros parámetros sugeridos pueden variar dependiendo de la máquina de láser utilizada y la potencia de láser disponible.
Retire la lámina protectora de la superficie de la plancha TroLase o TroLase y luego coloque el material en su láser. Si utiliza TroGlass Reverse se recomienda retirar la lámina después del proceso láser.
Parámetros láser:
Material | Color | Proceso | Potencia (%) | Velocidad (%) | ppi/Hz | Pasadas | Asistencia de aire | Offset Z | Dirección | Avanzado |
---|---|---|---|---|---|---|---|---|---|---|
TroLase Foil | black | Grabado CO2 | 55 | 80 | 500 | 1 | off | 1.5 | bottom to top | - |
red | Corte CO2 | 40 | 1 | 2000 | 1 | on | 0 | - | - | |
TroLase | black | Grabado CO2 | 65 | 80 | 600 | 1 | off | 1.5 | bottom to top | - |
red | Corte CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - | |
TroGlass Reverse | black | Grabado CO2 | 18 | 20 | 500 | 1 | on | 0 | bottom to top | - |
red | Cut CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - |

Paso 3: Montaje
Para unir las partes entre sí, primero hay que quitar la película protectora de la parte trasera del rótulo azul de TroLase. Ahora pegue la etiqueta TroLase en el TroLase amarillo o en el TroGlass Reverse blanco según las marcas.
¡Las etiquetas ya están listas para su uso!
Por supuesto, puede producir estos carteles en todas las combinaciones posibles de colores y materiales.