Exclusiva portada de catálogo de LaserPaper
Descubra cómo puede fabricar portadas valiosas de catálogos, folletos u otros artículos impresos utilizando LaserPaper Wood.
Preparación
Required material
- 1 sheet of LaserPaper Wood maple
- material to cover the engraving table
Machine used
- Speedy 360
- 120 Watt
- 2" lens
- aluminum cutting grid table or honeycomb table
For this sample you can use any laser machine from the Speedy laser engraver series.
Important
- For the inner part, use paper with at least 150 g/m² to secure sufficient volume of the finished item
- Make sure that "Send Beziers and paths to driver" is activated in your software. Otherwise the registration marks are not recognized by JobControl® Vision.
Paso a paso
Step 1: Make design layout
Make your own design and adapt it to your needs. Print your design on the LaserPaper Wood or forward it to your trusted printer.
Because this sample is being engraved and cut, we put a hair cross in the middle of the print file instead of registration marks. This hair cross helps you to position the job precisely.
Send the graphic for the outer shell to the laser using the settings below:
Print settings:
Process mode | Resolution | Cut line |
---|---|---|
Standard | 500 dpi | none |
Halftone | Others |
---|---|
Colors | enhanced geometries, inner geometries first |
Step 2: Laser process
Adjust the parameter settings. The parameters can differ depending on the laser machine used and laser power available.
Tip:
Change the order of the colors in JobControl from red to blue so that the material is scratched first and cut second.
Laser parameters:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
black | Engraving CO2 | 20 | 50 | 500 |
red | Engraving CO2 | 12 | 1.5 | 1000 |
blue | Cutting CO2 | 5 | 1.5 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | +2.5 mm | - |
1 | on | - | - |
1 | on | +2 mm | - |

Step 3: Post-processing
Take the cover out of your laser and insert the core of the catalogue. Or if you are using a commercial printer, forward the cut-out cover to your printing representative to attach it to the catalogue.
Preparación
Material necesario
- 1 hoja de LaserPaper Wood arce
- Material para cubrir la mesa de grabado
Máquina usada
- Speedy 360
- 120 vatios
- Lente de 2 pulgadas (5 cm de distancia focal)
- Mesa de corte de aluminio o mesa en panal de abeja
Para hacer esta muestra se puede usar cualquier máquina láser de la serie de grabadoras láser Speedy.
Importante
- Para la parte interior, use papel de por lo menos 150 g/m² para asegurar el volumen suficiente del artículo terminado
- Asegúrese de que "Send Beziers and paths to driver" ("Enviar Beziers y rutas al controlador") esté activado en su software. De lo contrario, JobControl® Vision no reconocerá las marcas de registro.
Paso a paso
Paso 1: Hacer un diseño
Haga su propio diseño y adáptelo a lo que quiera cortar y grabar. Imprima su diseño en LaserPaper Wood o envíelo a su impresora habitual.
Como este archivo que le proponemos tiene que ser cortado y grabado, imprima primero sobre el LaserPaper Wood (Papel de madera) las marcas de registro para que el JobControl Vision pueda reconocerlas y cortar correctamente.
Envíe el gráfico al láser usando los ajustes mencionados abajo:
Ajustes de impresión:
Modo de procesamiento | Resolución | Línea de corte |
---|---|---|
Estándar | 500 dpi | Ninguno |
Medio tono | Otros |
---|---|
Colores | Geometrías mejoradas, primero las geometrías internas |
Paso 2: Procesamiento con láser
Ajuste los parámetros según indicado. Los parámetros pueden diferir dependiendo de la máquina láser que tenga y de su potencia.
Sugerencia:
Cambie el orden de los colores en JobControl de rojo a azul para que el material sea primero grabado y luego cortado.
Parámetros láser:
Color | Proceso | Potencia (%) | Velocidad (%) | ppi/Hz |
---|---|---|---|---|
Negro | Grabado CO2 | 20 | 50 | 500 |
Rojo | Grabado CO2 | 12 | 1,5 | 1000 |
Azul | Corte CO2 | 5 | 1,5 | 1000 |
Pasadas | Asistencia de aire | Offset en Z | Avanzado |
---|---|---|---|
1 | Activado | +2,5 mm | - |
1 | Activado | - | - |
1 | Activado | +2 mm | - |

Paso 3: Post-procesamiento
Retire la portada del láser y ponga el catálogo. Alternativamente, envíe la portada recortada a su impresora, para que termine el trabajo de impresión.
Un poco de inspiración
Debido a la veta de la madera, también la impresión en color se ve muy bien en este material.