Juego Cornhole
El cornhole, también conocido como tragabolas, es un juego que se originó en el Medio Oeste de Estados Unidos y que ha ganado en popularidad en bares, campus universitarios y los hogares. Es ideal para una barbacoa o una fiesta al aire libre.
Preparación
Required material
- 2 - 61 x 122 cm sections of 1.3 cm plywood
- 4 - 5 x 10 x 122 cm for the frame
- 4 - 5 x 10 x 61 cm for the frame
- 4 - 5 x 10 x 29 cm for the legs
- 4 - Carriage Bolts
- 4 - washers
- 4 - wing nuts
- Paint
- High gloss varnish, both spray and brush on
Used Trotec Laser
- for boards
Speedy 500, 200 watts, 2.0 inch lens - for bags
Speedy 300, 120 watts, 1.5 inch lens

Paso a paso

Step 1: Laser Engraving and Cutting the Boards
The American Cornhole Association requires platforms be a 61 x 122 cm rectangle made from 1.5 cm plywood. The front of the platform stands 6.5 to 10 cm tall and the back of the platform sits 30 cm off the ground.
Using a large format laser cutter, here we used a Trotec SP500, set one of the pieces of plywood in the laser. We had to place ours sideways, since we wanted to both cut and engrave at the same time. You can also use a smaller laser with a pass through and cut the plywood down to size with a saw. Most home improvement stores will do this for a small fee.
Laser settings
Speedy 500, 200 watts, 2.0 inch lens
Engraving: Power: 70%, Speed: 100%, Frequency: 500ppi, Z offset: 0.5cm (for a nice dark engraving mark), Air Assist: ON
Cutting: Power: 100%, Speed: 0.50%, Frequency: 1000Hz, Air Assist: ON

Step 2: Building the Box
Now to build the box. Use the 5 x 10 cm pieces to build two 61 cm x 122 cm rectangles using two screws on each corner.
Attach one sheet of plywood to each 5 x 10 cm frame, using drywall screws. I used four across the top and four across the bottom evenly spaced. Down each side I put a screw about every 30 cm. Counter-sink the screws slightly so that the bags will not snag.

Step 3: Leg Assembly
Now it's time for the legs. Get the 5 x 10 x 29 cm for the four legs. Make a full 9 cm radius cut on one end of each leg. To make the cut, measure 4.5 cm down the length of the 5 x 10 and draw a line across it. Place a compass point centered on that line then draw the arc. Use a jigsaw to make the cut.
Turn the box upside down; lay a leg parallel, flush up against one of the top corners with the radius side in the corner. Clamp into place. From the inside of the box, make a mark in the center of the 5 x 10 vertically inside the radius. Drill a 1.3 cm hole through the side of the box and through the support leg.
Fasten the legs to the platform using pairs of carriage bolts + washers + wingnuts. The legs will rotate for nicer storage.

Step 4: Paint and Varnish
Now we want to paint the sides of the box and a little into the top of the board. Fill any holes or cracks with wood filler and let dry. Mask off a 2.5 cm area around the outside of the top of the box, and using high gloss paint, paint the sides of the box and the 2.5 cm strip around the top of the box with at least 2 coats of paint.
Once this is dry, coat the entire top and sides of the box with a high gloss varnish to protect the engraved area and make the bags “slide” but not too slippery. Since the dark laser mark made while engraving is prone to smearing, we first coated it with a few layers of spray polyacrylic before using the heavier, brush on version. 5 – 10 coats total should be enough. You want the grooves made by the engraving to feel smooth and not interrupt the sliding of the bags.

Step 5: Bags
Cornhole bags are canvas bags measuring 15 cm x 15 cm and filled with one pound of feed corn. You can also fill them with plastic pellets to make them weather proof, but the corn lets off a small amount of dust when hitting the boards, which helps with getting the perfect slide when playing. Not being sewers, we ordered our bags from Now that you have all the parts of the set, it’s time to set it up and start playing. You can find the official rules to the game at the American Cornhole Association’s website - http://americancornhole.com/rules-resources/aco-official-cornhole-rules/Step 6: Game on!
Preparación
Material requerido
- 2 - Tablas de madera de 61 x 122 cm y 1.3 cm de grosor, y tablas de:
- 4 - 5 x 10 x 122 cm para el marco lateral
- 4 - 5 x 10 x 61 cm para el marco de los extremos
- 4 - 5 x 10 x 29 cm para las patas
- 4 – Tornillos
- 4 – Juntas
- 4 – Tuercas de mariposa
- Pintura
- Barniz
Laser usado por Trotec
- SP500
- 200 vatios
- lente de 2.0 pulgadas

Paso a paso

Paso 1: Cortar y grabar con láser las tablas
La Asociación Americana de Cornhole requiere para jugar, 2 plataformas rectangulares de 61 x 122 cm, hechas en madera contrachapada de 1,3 cm de grosor. La parte frontal de la plataforma tiene una altura de 6,5 a 10 cm y la parte posterior se tiene que levantar 30 cm del suelo.
Para hacer las plataformas hemos usado un láser de Trotec SP500, también se puede usar un láser más pequeño con opción de apertura trasera, para grabar la madera y luego cortarla con una sierra.
Configuración del láser:
Trotec SP500 200 vatios
Cortar: Potencia – 100, Velocidad - .50, Frecuencia - 1000 Aire Asistido: ON
Grabar: Potencia – 70, Velocidad – 100, Frecuencia – 500, Z offset - .18 (para obtener marcas de grabado más oscuras) Aire Asistido: ON

Paso 2: Construir las cajas
Use las piezas de 2x4 para crear 2 ractángulos de 48" x 24" pulgadas usando tornillos en cada esquina. Una a esto los marcos de 2 x 4 pulgadas usando los tornillos. Nosotros hemos necesitado 4 para arriba y 4 para abajo. Debajo de cada lado hemos puesto un tornillo de 12 pulgadas.

Paso 3: Montar las patas de la caja
Use los trozos de madera de 5 x 10 x 29 cm para las patas. Corte un radio de 9 cm pulgadas al final de cada pata. Ayúdese de un compás para dibujar el semicírculo de 4,5 pulgadas que hay que cortar con sierra, en cada pata.
Dele la vuelta a la caja. Coloque cada pata con la parte cortada en semicírculo hacia abajo (que toque con la parte superior de la caja) y taladre agujeros en los laterales y las patas para unirlos, usando los tornillos, las juntas y las tuercas de mariposa. La idea es que estas patas se puedan plegar rotando.

Paso 4: Pintar y barnizar
Si pintamos y rellenamos las posibles irregularidades de la plancha de madera con cera para madera, nos quedará un resultado perfecto. Como el Cornhole es un juego de exterior, conviene usar un barniz para muebles de exterior y poner 2 capas. Este barniz además ayudará a que las bolsas de grano resbalen mejor por la madera.

Paso 5: Bolsas
Las bolsas de Cornhole tienen un tamaño de 15x15 cm y están rellenas con 1/2 kilo de grano. También se pueden rellenar con bolitas de plástico para que duren más. Para personalizar nuestras bolsas (grabar la tela con láser) hemos usado una Speedy 300 de 120 vatios. El láser le dará un aspecto desgastado al tejido, sin comprometer su resistencia.
Configuración del láser:
Trotec Speedy 300 120 vatios
Grabado: Potencia – 30, Velocidad– 100, Frecuencia – 500

Paso 6: ¡A jugar!
Ahora que tiene todas las partes del juego, es hora de jugar. En esta página web podrá encontrar las reglas oficiales del juego - http://americancornhole.com/rules-resources/aco-official-cornhole-rules/
