Rodillo de cocina

Este tutorial le muestra cómo realizar un grabado profundo en un rodillo para hacer divertidas formas en su masa.

Grabado con láser de rodillo de cocina
Grabado con láser de rodillo de cocina

Preparación

Required material
  • rotary attachment
  • wood rolling pin
  • application tape
  • a cleaning brush and some water
Used Trotec Laser
  • Speedy 300
  • 120 watts
  • 2.0 inch lens
Rodillo de cocina de roble

ZIP

Descargar ahora
laser conejo Pascua
csm_Oak-Rolling-Pin_07ba6df148.png

PDF

Descargar ahora

Paso a paso

laser engraved rolling pin
Step 1

Step 1: Set Up Your Graphics

When creating your graphics, you want the finished file to be as wide as the circumference of your rolling pin and as tall as your rolling pin barrel.

As a quick geometry refresher – the diameter is how wide the barrel of the rolling pin is if you measured from the two widest outside points across the barrel. The circumference is the length if you wrapped a tape measure around the outside of the barrel. You can easily find the circumference if you take the diameter measurement and multiply it by 3.14.

Remember that if you are using text, the image needs to be reversed so that the text looks backwards. This ensures that the text is reading the correct way when it is embossed in the dough.

Rodillo-amasar-madera
Step 2

Step 2: Prep the Rolling Pin

With the high power for deep engraving, make sure that the non-lasered parts of the barrel remain clean of soot and scorching by masking the entire rolling pin. You can use application tape, which is like a large roll of making tape, or masking or painters tape. Make sure that the tape is as even and bubble-free as possible.

Rodillo para amasar
Step 3

Step 3 - Laser Settings

Import the PDF file into Corel Draw, customize it as you want to or take your own design and send it to the laser. Make sure that you have activated the rotary attachment and entered the diameter of the rolling pin in the properties dialog.

Engraving:

Power: 100% - Speed: 15% - Frequency: 500 ppi - Air Assist: ON

Step 4

Step 4 - Cleaning

Once the laser has finished, remove the rotary, take off the application tape and inspect the rolling pin for smoke residue. A good scrubbing with a dish brush and some soap will make sure that all the dust in the engraving does not get in your dough. If the rolling pin is unfinished, any extra smoke residue left on the barrel can be lightly sanded off.

Now, time to enjoy some delicious giraffe imprinted cookies!

Tips

The attached file is for a rolling pin that is 25,4 cm long and 6,07 cm in diameter.

Preparación

Material requerido
Láser usado por Trotec
  • Speedy 300
  • 120 vatios
  • lente de 2.0 pulgadas
Rodillo de cocina de roble

ZIP

Descargar ahora
laser conejo Pascua
csm_Oak-Rolling-Pin_07ba6df148.png

PDF

Descargar ahora

Paso a paso

laser engraved rolling pin
Step 1

Paso 1: Adaptación del gráfico

Cuando elija o cree el gráfico que quiere grabar, tenga en cuenta que tiene que ser tan ancho como la circunferencia de su rodillo y tan alto como sea éste.

Como pequeño recordatorio– tenga en cuenta que el tamaño de una circunferencia se mide multiplicando su diámetro (la distancia entre los puntos más separados de la circunferencia) por 3.14. -

Si el motivo grabado va a ser texto, recuerde "darle la vuelta" a la imagen, para que el texto quede legible del derecho tras grabarlo.

Rodillo-amasar-madera
Step 2

Paso 2: Preparación del rodillo

Como la potencia va a estar al máximo para conseguir un grabado profundo, para que las partes que no van a ser "laseradas" no se manchen de residuos de madera, cubra todo el rodillo con cinta adhesiva. Cuanto más ancha sea la cinta más fácil será cubrir el rodillo. Asegúrese de que no quedan burbujas entre la cinta y el rodillo.

Rodillo para amasar
Step 3

Paso 3: Configuración del láser

Importe el PDF que hemos preparado a su Corel Draw, customícelo como quiera o haga su propio diseño. Compruebe que ha activado el accesorio rotatorio en el programa del láser y que ha introducido correctamente el diámetro del rodillo.

Grabado:

Potencia: 100% - Velocidad: 15% - Frecuencia: 500 ppi - Aire soplado: ON

Step 4

Paso 4: Limpieza

Una vez terminado el grabado, retire el accesorio rotatorio, quite también la cinta adhesiva y compruebe la profundidad del grabado. Frotando el rodillo con un cepillo, agua y jabón, conseguirá quitar las posibles manchas y residuos que se han podido generar sobre el material, por el trabajo con láser.

Y por último... ¡ya puede hacer galletas con jirafas!

Consejo:

Para facilitar el proceso puede usar la plantilla que hemos preparado para nuestro rodillo, que mide 25,4 cm de largo y 6,07 cm de diámetro.

Serie Speedy
La grabadora láser y la máquina de corte ideales para la personalización.

Descubra las grabadoras y máquinas de corte láser

¿Tiene preguntas sobre las aplicaciones o la configuración?
Nos complace asesorarle desde la A de asistencia de aire hasta la Z de offset Z.

Solicitar más información.

Miembro orgulloso del troGROUP Logo