Carcaj de fieltro
Corte y grabe con láser su carcaj personalizado de fieltro y madera, y dé en la diana con sus flechas.
Preparación
Required material
- 4mm Polyesterfelt in any color
- 3.5mm solid wood alder
- wool in any color
- sticky tape
Used Trotec Laser
- Speedy 400
- 80 watts
- 2.0 inch lens
Tip
Vacuum table with honeycomb cutting tabletop or aluminum cutting grid table

Paso a paso
Step 1: Design
Import the PDF file into Corel Draw and select your desired model and the design for either felt or wood (see the tabs below the working area in Corel Draw).
Step 2: Laser parameters
Felt:
Engraving: Power: 33% - Speed: 50% - Frequency: 500 ppi - Air Assist: ON
- Advanced: Optimized Quality
Cutting: Power: 40% - Speed: 2% - Frequency: 1000 Hz - Air Assist: ON
Wood:
Engraving: Power: 60% - Speed: 50% - Frequency: 500 ppi - Air Assist: ON
Cutting: Power: 100% - Speed: 1.8% - Frequency: 1000 Hz - Air Assist: ON

Step 3: Laser cut and engrave felt and wood
Before you begin with the cutting and engraving process, be sure to cover the cutting table around the felt with cardboard and sticky tape. This way the felt is properly fixed for laser cutting and engraving.
You can adjust the size of the felt in CorelDraw according to the length of the arrows you will be putting into your quiver. Our sample is best suited for very long arrows.
Send the file with the perfect size to your laser cutter. After you've taken the felt out of the laser, put your hardwood board inside. Now send the file for laser cutting and engraving the bottom part of the quiver to the laser.

Step 4: Sewing the pieces
Next you have to sew the round wooden plate and the felt along the holes together. Take the side with the pattern and sew it onto the wooden plate. Make sure the engraving will be on the outside. Sew the felt along the length and the remaining holes at the top together.
Our quiver is ready for your next archery training session. our quiver is ready for your next archery training session!
Preparación
Material requerido
- Fieltro, 4 mm
- Madera sólida, grosor 3.5 mm
- Lana
- Cinta de pintor
Láser usado por Trotec
- Speedy 400
- 80 vatios
- lente de 2,0 pulgadas
Consejo
La mesa de corte tipo panal de abeja es la más adecuada para conseguir los mejores resultados. Lo ideal es usarla combinada con la mesa de vacío.

Paso a paso
Paso 1: Preparación
Descargue e importe el archivo PDF en Corel Draw y seleccione el diseño que más le guste de las pestañas que en encontrará en el documento.
Paso 2: Configuración del láser
Fieltro:
Grabado: Potencia: 33% - velocidad: 50% - Frecuencia: 500 ppi - Aire soplado: ON - Alta calidad
Corte: Potencia: 40% - velocidad: 2% - Frecuencia: 1000 Hz - Aire soplado: ON
Madera:
Grabado: Potencia: 60% - velocidad: 50% - Frecuencia: 500 ppi - Aire soplado: ON
Corte: Potencia: 100% - velocidad: 1.8% - Frecuencia: 1000 Hz - Aire soplado: ON

Paso 3: Cortar y grabar los materiales
La aljaba se fabrica con dos materiales distintos, comenzaremos con el fieltro. Para mantener el material plano sobre la superficie de trabajo utilizaremos la mesa de efecto vacío. Puede ajustar el tamaño de la aljaba en su programa de diseño según la longitud de las flechas que va a guardar, nosotros hemos utilizado las medidas más adecuadas para las flechas de gran tamaño. Una vez terminemos con el fieltro pasaremos a grabar y cortar la madera, la cual vamos a cubrir con cinta de pintor antes de procesarla con láser, con el fin de que no queden manchas de humo. Cuando acabe el grabado y el corte podremos retirar la cinta.

Paso 4: Coser
Finalmente coseremos la pieza de madera al fieltro asegurándonos de que el grabado queda en el exterior. A continuación cosemos a lo largo de la estructura cilíndrica y los agujeros que quedan en la parte superior y ¡listo! ya tenemos nuestra aljaba personalizada.