Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
See in this DIY sample how you can make a great wall decoration using different Trotec materials.
For this sample you can use any laser machine from the Speedy laser engraver series.
Thanks to the big range of Trotec materials, you can offer alternative colors for your customers easily
Make your own design or import our template. Adapt it to your requirements. Send the job to the laser using the driver settings below.
Process mode | Resolution | Cut line |
---|---|---|
Vector Job | 1000 dpi | None |
Halftone | Others |
---|---|
Color | Optimized geometries |
Position the first TroGlass material on the acrylic cutting grid of your Trotec laser and cut the individual pieces. Do the same with the other materials as well. You can leave the protective foil on the material if you want. We removed it because we did not want to remove them for every single piece. Please note that the parameters used can differ depending on the laser machine used and the available laser power:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut CO2 | 100 | 0.9 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | On | - | - |
Since we wanted to have a large overall design, we used a SP500 laser cutter for cutting the black back plate. The Speedy 360 was too small to do the job. If you do not have such a large working area, you can either reduce the complete graphic or cut a round base plate only.
The two half circles of TroLase foil are the all-over background on which we put the individual pieces. Send the half circle to the laser using the following parameters:
Process mode | Resolution | Cut line |
---|---|---|
Vector Job | 1000 dpi | None |
Halftone | Others |
---|---|
Color | Optimized geometries |
Put the TroLase Foil on the acrylic grid and cut the half circle using the following parameters. You will need 2 pieces.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut CO2 | 40 | 2 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | On | - | - |
Now you can send the design for MDF and solid wood maple using the following parameters:
Process mode | Resolution | Cut line |
---|---|---|
Vector Job | 1000 dpi | None |
Halftone | Others |
---|---|
Color | Optimized geometries |
Change the acrylic cutting grid against the honeycomb cutting table and cut the maple wood using the following parameters:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut CO2 | 100 | 1.4 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | On | - | - |
We recommend to use the small nozzle and a lot of compressed air (if available) for clean cutting edges
Put the MDF plate into your Trotec laser and cut the single pieces using the following parameters:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Red | Cut CO2 | 90 | 0.4 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | On | - | - |
The most time-consuming part of this sample is certainly the assembly of the decoration.
First glue the two star like base plates with the circle of TroGlass Satins. Make sure that the two large pieces are well positioned edge to edge. Now turn the decoration and remove the protective foil (if you haven't removed it before cutting). Fix the two half circles of TroLase Foil. Now take the time to apply the pieces of the different materials.
Glue it on the white base plate only when you are sure that they are positioned correctly. It is helpful to have an image of the finished graphic to hand. You will find this image in the download document provided.
If all pieces have been fixed, you can mount the decoration on the wall using the mounting devices.
You can use this decoration as a wall clock as well. In this case you just have to cut a hole in the middle and insert the clockwork from the back
By combining other TroGlass colors and wood types, you can easily create a version that fits perfectly into any office, clubhouse, lounge, etc.