Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Produce stamps for individual packagings. Ideal for small quantities.
The stamp rubber can of course also be processed with other laser engravers of the Speedy series.
Create your own design or use our free template. A tip for creating your own design: strong, not too detailed motifs and fonts are best. Avoid too fine lines - a lot of material will be removed, too thin lines can become unstable.
Find more information in our tips & tricks section: stamp engraving
Now send the job to the laser with the settings below.
Dimension | Process mode | Resolution | Cut line |
---|---|---|---|
Professional 5212 or user-defined size 116 x 70 mm | Stamp | 500 dpi | optimized |
Halftone | Shoulders | Others |
---|---|---|
black-white | medium | optimized geometries |
Make the parameter settings. Our suggested parameters may vary depending on the laser machine used and the available laser power.
Insert the laser rubber Aero+ 5 mm into the machine. Make sure that it can no longer slip, as in this process the stamp rubber is vaccuumed off after each engraving pass. A fixation can be achieved by this:
Cover the remaining work surface to create vacuum
Set the "Cut" to "Skip" in the parameter settings. Focus and position the laser, then start the first engraving pass. After engraving, vacuum well the dust on the rubber plate with a vacuum cleaner. Make sure that the rubber does not slip. Now repeat the engraving process three more times.
Note: focus again before each pass (on the new level) and vacuum the stamp plate after each pass.
After the engraving the cut takes place. Activate "Cut CO2"" in the parameter settings and skip "Engrave CO2".
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Black | Engrave CO2 | 100 | 15 | 1000 ppi |
Red | Cut CO2 | 100 | 0.5 | 1000 Hz |
Passes | Air assist | Z-offset | Direction | Advanced |
---|---|---|---|---|
1 | on, maximum air assist | - | top down | optimized quality |
1 | on | - | - | - |
Remove the laser rubber from the laser device and then clean it with a fine brush and water. After drying, glue the stamp plate onto the stamp.
Stamp a few times on a kitchen paper. Then the stamp is ready for use!
With this stamp you can individualise your packaging quickly and easily. Your logo can be applied to paper bags, carrier bags, envelopes and cartons to further increase the visibility of your business.
As an alternative to the above-mentioned settings with four engraving passes, depth engraving can also be carried out in three passes with a resolution of 1,000 dpi, as more material is removed at higher resolutions.
However, the time required for this variant remains almost identical to the above mentioned application, as the laser needs more time for engraving with higher resolution.
Perform the laser processes as described above.
Use the following print and parameter settings for the laser process in three engraving passes.
Dimension | Process mode | Resolution | Cut line |
---|---|---|---|
Professional 5212 or user-defined size 116 x 70 mm | Stamp | 1000 dpi | optimized |
Halftone | Shoulders | Others |
---|---|---|
black-white | medium | optimized geometries |
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
Black | Engrave CO2 | 100 | 25 | 1000 ppi |
Red | Cut CO2 | 100 | 0.5 | 1000 Hz |
Passes | Air assist | Z-offset | Direction | Advanced |
---|---|---|---|---|
1 | on, maximum air assist | - | top down | optimized quality |
1 | on | - | - | - |