Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
"Wash hands" + "Keep distance"
Here you will find templates for the quick creation of Covid-19 signs from TroLase, TroLase Foil and TroGlass.
Sign "Wash your hands" Variant 1
Sign "Wash your hands" Variant 2
This sample can be produced with any other machine of the Speedy laser engravers.
When working with TroLase or TroLase Foil, the following applies: If you use the entire work surface, use a vacuum table or an adhesive mat so that the material lies flat over the entire surface. Otherwise, cover the work surface with paper to create an optimal vacuum.
Create your own design or use our template. Now send the job to the laser with the settings below.
Important: If you use TroGlass Reverse, the file must be mirrored.
Process mode | Resolution | Cut line |
---|---|---|
standard | 500dpi | none |
Halftone | Other |
---|---|
- | Optimized geometries, inner geometries first |
Now make the parameter settings. Our suggested parameters may vary depending on the laser machine used and the available laser power.
Remove the protective foil from the TroLase Foil or TroLase surface and then place the material in your laser. If you use TroGlass Reverse it is recommended to remove the foil after the laser process.
Material | Color | Process | Power (%) | Speed (%) | ppi/Hz | Passes | Air Assist | Z-Offset | Direction | Advanced |
---|---|---|---|---|---|---|---|---|---|---|
TroLase Foil | black | Engrave CO2 | 55 | 80 | 500 | 1 | off | 1.5 | bottom to top | - |
red | Cut CO2 | 40 | 1 | 2000 | 1 | on | 0 | - | - | |
TroLase | black | Engrave CO2 | 65 | 80 | 600 | 1 | off | 1.5 | bottom to top | - |
red | Cut CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - | |
TroGlass Reverse | black | Engrave CO2 | 18 | 20 | 500 | 1 | on | 0 | bottom to top | - |
red | Cut CO2 | 60 | 1 | 2000 | 1 | on | 0 | - | - |
To attach the parts to each other, first remove the protective film on the back of the blue TroLase shield. Now stick the TroLase label onto the yellow TroLase or the white TroGlass Reverse label according to the markings.
The signs are now ready for use!
You can of course produce these signs in all possible colour and material combinations.