Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Learn how you can produce a decorative and extraordinary Mother's Day gift.
optional:
For this sample you can use any laser machine from the Speedy laser engraver series.
You can use leftover material for the "blossoms."
Make your own design or import our template. Adapt it to your requirements. Send the job for laser cuttting the base plate to the laser using the driver settings below.
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
Color | Optimized geometries, inner geometries first |
Put the TroGlass Clear on the acrylic cutting grid of your Trotec laser and insert the 2.5" lens. Then cut the base using the following settings. The parameters can differ depending on the laser machine used and laser power available.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 95 | 0.2 | 20000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | -3 mm | - |
We used the standard parameters TroGlass Clear (speed optimized) from JobControl® .
Send the design for the grass to the laser using the settings below.
Process mode | Resolution | Cut line |
---|---|---|
Standard | 500 dpi | none |
Halftone | Others |
---|---|
Color | Optimized geometries |
Put the dark green transparent TroGlass onto the acrylic cutting grid of your Trotec laser. Use the 2" lens for this and all following tasks for this application. Engrave and cut the design with the following parameters. The parameters can differ depending on the laser machine used and laser power available.
Process | Color | Process | Power (%) | Speed (%) |
---|---|---|---|---|
Engraving | black | Engrave CO2 | 14 | 20 |
Cutting | red | Cut CO2 | 100 | 1 |
ppi/Hz | Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|---|
500 | 1 | on | 0mm | High Quality |
1000 | 1 | on | - | - |
Start the engraving process from the bottom so that the dust cannot settle on the engraved area.
The next step is to send the design of the solid wood stem to the laser using the driver settings below.
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
- | Optimized geometries |
Change the acrylic cutting grid against the honeycomb cutting table and position the walnut sheet. Cover the rest of the engraving area to maximize vacuum. Cut the material using the parameters below:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 100 | 1 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | - | - |
By covering the engraving area, you produce a vacuum which is essential for a clean and consistent cut.
Finally, send the design of the abstract blossoms to your laser.
Process mode | Resolution | Cut line |
---|---|---|
Cut Job | 1000 dpi | none |
Halftone | Others |
---|---|
- | Optimized Geometries, Inner Geometries first |
Put the maple veneer sheet into the laser, and carefully cover the rest of the engraving table. Then cut the blossoms using the following parameters:
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
red | Cut CO2 | 100 | 1.2 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | - | - |
If you cut the entire sheet, focus on the middle of the material to compensate for any differences in thickness.
Put the stem into the base and decorate it with the blossoms. You can combine large and small blossoms. Finally, position the grass into the base, and this inventive Mother's Day bouquet is ready.
Twisted blades of grass are an additional eye catcher. To make these, position the "blades of grass" into a bench vice or another heat-resistant holder. Take a hot air gun and carefully heat the filigree grass. Then deform and twist the hot acrylic. Don't forget to wear gloves! Hold the acrylic in place until it is cooled down. With a little practice, you can get impressive objects.
Use other colors of TroGlass Satins and transform the "flower bouquet" into an abstract sculpture.