Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Step by step instruction
Check out our roll up pencil case selection for the very best in unique or custom, handmade pieces from our office & school supplies shops. These roll up pencil cases offer an elegant and distinctive alternative to conventional zipper or snap fastener cases.
LaserLeather can of course also be processed with another laser engraver of the Speedy series. Adjust the parameter settings according to your machine.
Create your own design or use our template. Now send the job to the laser with the settings below.
Process mode: | Standard |
---|---|
Resolution: | 500dpi |
Cut line: | none |
Halftone: | Color |
Others: | Optimized geometries, inner geometries first, minimize to job size |
Now make the parameter settings. Our suggested parameters may vary depending on the laser machine used and the available laser power.
To process the LaserLeather, use the vacuum table with honeycomb table top and the nozzle with the small hole diameter. Put the LaserLeather into the laser machine. Cover the rest of the working surface around the material to create a vacuum and achieve good exhaust performance.
Then start the engraving and cutting process.
Engrave | Cut | |
---|---|---|
Color | Black | Red |
Process | Engrave CO2 | Cut CO2 |
Power (%) | 60 | 20 |
Speed (%) | 100 | 2 |
ppi/Hz | Auto | 1000 |
Passes | 1 | 1 |
Air Assist | ON | ON |
Z-Offset | +1 | - |
Direction | Bottom to top | - |
Advanced | Optimized Quality | - |
After the laser process, remove all cut parts from the laser. If necessary, clean the cut parts carefully with a slightly moistened cloth.
Insert the wide band from the bottom through the first slit so that the four small holes on the band are exactly over the four holes of the pin roll.
Now thread the narrow band through the four small holes so that the band crosses over on the upper side.
Turn the pencil roll over and knot the thin tape on the back. Then shorten the ends with scissors.
Now place the pins one after the other on the inside of the roll and pull the wide band through the slots so that the pins are fixed in the roll. Tighten the tape well, so that the pins get a good grip.
Pull the ribbon through the slit at the top edge of the pencil roll.
Finally, wrap the tape once around the outside of the roll. Fix the end by pulling it once under the tape.
A two-tone artificial leather for a variety of laser applications: LaserLeather. From bags, backpacks, labels, jewelry, or, as shown here, a stylish storage option - the LaserLeather can transform into many unique pieces due to its easy processing. Intricate laser engravings and laser cuts are possible, where the second color layer can be shown and add dimension.
Make the pen roll also in other colors of the LaserLeather! By adding your name or your own design, the product can also be personalized or individualized very easily.
Develop your creativity and discover the different color combinations: