Trotec Laser Inc.
Customer support
Phone: (734) 927-6300
E-Mail: usa@troteclaser.com
Contact form 
Jewellery Display
Request a demoSee how you can produce an individual jewelry display using different acrylic sheets.
Preparation
Required material:
- 1/4 sheet TroGlass Clear 8 mm
- 1/4 sheet TroGlass Clear 5 mm
- 1/4 sheet TroGlass Satins Orange translucent with double-sided adhesive foil on both sides
Machine used:
- Speedy 400
- 120 Watt
- 2.5" lens
- Acrylic lamella or vacuum table with acrylic grid or distance holders
This sample can be produced with any machine of Speedy family or SP series. For high-quality and efficient cutting of 8 mm acrylic you need laser power of 80 W or more.
Important:
- Remove the protection foil from top of the 5 mm and 8 mm acrylic before laser processing
- Cover the rest of the working area for a better vacuum effect
Step by Step
Step 1: TroGlass Clear 8 mm
Import our design template into your graphic program. Send the job to your laser using the parameters mentioned below.
Print settings
| Process mode | Resolution | Cut line |
|---|---|---|
| Standard | 500 dpi | none |
| Halftone | Others |
|---|---|
| Color | enhanced geometries |
Step 2: Laser process TroGlass Clear 8 mm
Now make the parameter settings. Our recommendations can vary depending on the laser type and laser power.
Tips:
For an even better result, cut the shape first and engrave the design afterwards
Laser Parameters
| Color | Process | Power (%) | Speed (%) | ppi/Hz |
|---|---|---|---|---|
| black | engrave CO2 | 23 | 75 | 500 |
| red | cut CO2 | 95 | 15 | 20.000 |
| Passes | Air Assist | Z-Offset | Advanced (plate set up) |
|---|---|---|---|
| 1 | on | - | Engraving direction from bottom |
| 1 | on | -2.5 mm | - |
Step 3: TroGlass Clear 5 mm
Import our design template into your graphic program. Send the job to your laser using the parameters mentioned below.
Print settings
| Process mode | Resolution | Cut line |
|---|---|---|
| Standard | 500 dpi | none |
| Halftone | Others |
|---|---|
| Color | enhanced geometries |
Step 4: Laser process TroGlass Clear 5 mm
Now make the parameter settings. Our recommendations can vary depending on the laser type and laser power.
Laser Parameters
| Color | Process | Power (%) | Speed (%) | ppi/Hz |
|---|---|---|---|---|
| red | cut CO2 | 50 | 0.2 | 20.000 |
| Passes | Air Assist | Z-Offset | Advanced |
|---|---|---|---|
| 1 | on | -1.5 mm | - |
Info:
- We used the JobControl® standard parameters optimized for quality
- The material parameters of JobControl® can be downloaded from www.troteclaser.com
Step 5: TroGlass Satins
Import our design template into your graphic program. Send the job to your laser using the parameters mentioned below.
Print settings
| Process mode | Resolution | Cut line |
|---|---|---|
| Standard | 500 dpi | none |
| Halftone | Others |
|---|---|
| Color | enhanced geometries |
Step 6: Laser process TroGlass Satins
Now make the parameter settings. Our recommendations can vary depending on the laser type and laser power.
Laser Parameters
| Color | Process | Power (%) | Speed (%) | ppi/Hz |
|---|---|---|---|---|
| red | cut CO2 | 30 | 0.2 | 20 kHz |
| Passes | Air Assist | Z-Offset | Advanced |
|---|---|---|---|
| 1 | on | - | - |
Info:
- We used the JobControl® standard parameters optimized for quality
- The material parameters of JobControl® can be downloaded from www.troteclaser.com
Step 7: Post-processing and assembly
To assemble the parts, first glue the colored acrylic parts on the 5 mm clear acrylic. Make sure that the pieces are exactly positioned above each other. Next position the 8 mm acrylic part with the engraving inside on the colored parts. By doing this the engraving is protected.
Inspirations
For an even more individual presentation of your jewelry, use displays in other shapes, material thicknesses and material combinations. If you are using only few thin acrylic sheets, cut a base to let the display stand stable.
