Speedy series: Laser engraving and cutting machines for formats up to 1016 x 610 mm
⚫ Engrave | ⚫ Cut | ⚫ Mark |
Laser type: | CO₂, Flexx or Fiber laser |
---|---|
Work area: | 610 x 305 up to 1016 x 610 mm |
Max. workpiece height: | 125 - 305 mm |
Laser power: | 20 - 120 watts |
SP series: CO2 laser cutter for large-format materials.
⚫ Engrave | ⚫ Cut | ⎯ Mark |
Laser type: | CO₂ laser |
---|---|
Work area: | 1245 x 710 up to 3250 x 3210 mm |
Max. workpiece height: | 50 - 112 mm |
Laser power: | 40 - 400 watts |
Marking laser stations with galvo marking heads. Marking area up to 44.1 x 25.0 inch.
⚫ Engrave | ⎯ Cut | ⚫ Mark |
Laser type: | CO₂ or Fiber laser |
---|---|
Max. work area: | 190 x 190 up to 1300 x 450 mm |
Max. workpiece height: | 250 - 764 mm |
Laser power: | 20 - 100 watts / 20 + 100 watts MOPA |
Make your own photoengraved menu card out of Trotec TroLase material.
You can also create this sample using any machine from the Speedy series.
You can start by creating your own design, or you can use our template. With the integrated Photo mode, our JobControl Laser Software supports you perfectly when engraving photos. Get more detailed information and tips and tricks for photoengraving here:
Send your design to the laser using following settings:
Process | Resolution | Cut line |
---|---|---|
Photo optimized | 600 dpi | none |
Halftone | Others |
---|---|
Ordered dithering | - |
Set the parameters as described below. The laser parameters may vary depending on the type of laser machine you are using and available laser power.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
black | engraving CO2 | 50 | 80 | 600 |
red | cutting CO2 | 6 | 5 | 1000 |
blue | cutting CO2 | 60 | 1.2 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 1 mm | - |
1 | on | - | - |
1 | on | - | - |
Remove the protective foil from the pink TroLase material and put it into your Trotec laser. Run the engraving (black) and the cut jobs (red and blue).
As an eye catcher, we combined two different materials for our menu card. Send the second graphic, the rhombic pattern, to your Trotec laser by using the following parameters:
Process mode | Resolution | Cut line |
---|---|---|
Standard | 600 dpi | none |
Halftone | Others |
---|---|
color | - |
Put your TroLase Thin material in your Trotec-Laser. Remove the protective foil, run the engraving job from bottom to top, and cut the job.
Because of the size it is important to have very good vacuum. You can increase your vacuum power by covering the rest of your working area with paper.
Color | Process | Power (%) | Speed (%) | ppi/Hz |
---|---|---|---|---|
black | engraving CO2 | 60 | 80 | 600 |
red | cutting CO2 | 30 | 1.5 | 1000 |
Passes | Air Assist | Z-Offset | Advanced |
---|---|---|---|
1 | on | 1 mm | High Quality |
1 | on | - | - |
Clean the surface and the edges of both TroLase-materials with a damp cloth. Take the rhombic pattern and apply it to the photoengraved cover. Finally, add your content to the menu card and clip it with the binding screw. And voilà - be proud of your unique menu card.
You can print the content-sheets of your menu card and cut it with the laser. Our JobControl® Vision laser software then supports you in cutting out the printed sheets with highest precision.
Of course you can also create amazing menu cards out of materials like TroGlass or our Trotec Wood. Here are some samples.