--------------------------
diy nursery mobile 2

Mobile from TroGlass Pastel

Manufacture this individual mobile out of different acrylic materials.

Preparation

Materials required
  • TroGlass Pastel 3mm (for the bodies of the elephants) each 1/4 plate in mint, yellow, orange, lilac, pink, light blue
  • TroGlass Satins 3mm (for the ears, hearts and for the tire for the suspension) each 1/4 plate in lime green, yellow, orange, violet, fuchsia, blue
  • Cotton thread or silk

TroGlass acrylic is available to order from our engraving supplies webshop.

Laser cutting machine used
  • Speedy 360, 80 watts
  • 2" lens
  • Nozzle with large opening
  • Air assist low
  • Acrylic cutting grid table

Other machines of the Speedy laser engraver series can be used to create the mobile. 

Tip

This tutorial is an excellent way to experiment with combining different colours to create a striking mobile. 

trotec-laser-nursery-mobile.zip

ZIP

Download now

Step by step

trotec acryl pastel
Step 1

Step 1: Create your own design or use our template

Make sure that the cutting gap corresponds to the thickness of the material so that the individual parts can then be inserted into each other.
Laser cutting according to our template:

  • 1x suspension ring large
  • 1x suspension eyelet small
  • 8x elephant (in different colours)
  • 8x ears (with desired motives in different colours)
  • Heart large (in desired number and colour)
  • Heart small (in desired number and colour)

Use the desired colour combinations to create the print jobs for the respective acrylic plates.
Now send the corresponding job to the laser using the settings below.

Print Settings

Process mode Resolution Cut line
Standard 500 dpi none
Halftone Others
Colour optimised geometries 
inner geometries first
trotec-laser-parameter-acryl-pastel
Step 2

Step 2: Laser Cutting TroGlass

The next step is to create the parameter settings. These parameter settings apply to both TroGlass Pastel (3mm) and TroGlass Satins (3mm). Please note that our suggested parameters may vary depending on the laser machine used and the available laser power.

Leave the protective film on both the top and bottom of the acrylic sheets. Place the material on the acrylic grid cutting table in the laser cutting machine. Cover the remaining surface to create the best possible vacuum using a suitable material. Perform the laser process for each acrylic sheet accordingly.

Laser parameters

Colour Process Power (%) Speed (%) ppi/Hz
Blue Cut CO2 10 1 1000 Hz
Red Cut CO2 50 0.2 5000 Hz
Passes Air Assist Z-Offset Direction Advanced
1 ON - - Correction 10
1 ON - - Correction 10
Step 3

Step 3: Assemble the elephants

Once the laser cutting process has been completed, remove the parts from the laser machine. Peel off the protective foil from the top and bottom of the individual design parts.

Prepare all cut out parts.
Put the ears together with the respective part of the torso.
Combine the colours as you wish to create a striking effect.

Step 4

Step 4: Attaching the thread

Now thread a thread through the hole at the head of the elephant.
Then feed the same thread from the other side through the hole in the fuselage.
The resulting crosshairs fix the ears to the elephant's trunk.
Knot the thread above the ears.
Follow these steps for all elephant models.

Step 5

Step 5: Assembly

Now thread two threads of the desired length for the suspension into the opposite, larger holes on the ring. Make sure to also pull the thread through the small oval ring for the suspension.
Hold the tire by the suspension and adjust the length of the threads so that the ring hangs horizontally. Knot the ends.
Finally, hang all elephants and hearts in the desired arrangement in the holes provided on the ring.

TroGlass Pastel – fresh and lively pastel-coloured acrylic

TroGlass Pastel is the newest addition to the Trotec range of engravable materials for laser cutting and laser engraving. These new acrylic sheets make your applications pop with vibrant colours and feature all the benefits of cast acrylics. TroGlass Pastel features one gloss and one matt side, broadening the range of creative applications possible with the material. Available in standard sheet size (1216x606 mm), all TroGlass pastel sheets are 3mm thick. 

Be fully in trend with TroGlass Pastel

Inspiration

Make each elephant individual and combine different colours!

This tutorial also works well with other materials, including woods. When using different materials, pay attention to the material thickness and adjust the cutting gap in the graphic accordingly if necessary.

Please note: this mobile is not a toy, it is only suitable for decoration purposes! Install the mobile out of reach of small children!

Speedy series
The ideal laser engraver and cutter for personalisation.

Discover laser engravers and cutters

Questions about applications or settings?
We're happy to advise you from A for Air assist to Z for z-offset.

Contact us
Proud member of troGROUP Logo